Trail Tech Striker Speedometer/Voltmeter User Manual

Introduction

The Trail Tech Striker is a digital speedometer and voltmeter designed to provide essential vehicle information. This device helps monitor speed, distance, time, battery voltage, and engine temperature, ensuring you have critical data at your fingertips for your Yamaha GRIZZLY 550 4x4.

This manual provides instructions for the proper installation, operation, and maintenance of your Striker unit.

Key Features

• Speed Display: Real-time speed measurement.
• 5 LED Group Backlight: Enhanced visibility in various lighting conditions.
• Voltage Monitor: Displays vehicle battery voltage to prevent unexpected power loss.
• Distance Tracking: Odometer and trip distance functions.
• Temperature Sensor: Monitors ambient or engine temperature.
• Accumulated Run Time: Tracks total operating hours.
• Maintenance Reminders: User-configurable alerts for service intervals.

Setup and Installation

Proper installation is crucial for the accurate and reliable operation of your Trail Tech Striker. While specific steps may vary slightly based on your vehicle's configuration, the general process involves mounting the unit, connecting the power, and installing the speed and temperature sensors.

1. Mounting the Unit: Securely attach the Striker unit to a suitable location on your Yamaha GRIZZLY, ensuring clear visibility and protection from direct impact.
2. Power Connection: Connect the unit's power wires to your vehicle's 12V DC power source, following the wiring diagram provided in the full installation guide (not included here). Ensure proper polarity.
3. Speed Sensor Installation: Install the magnetic speed sensor according to the vehicle-specific instructions. This typically involves attaching a magnet to a rotating part (e.g., wheel hub) and positioning the sensor to detect each rotation.
4. Temperature Sensor Installation: Install the temperature sensor to monitor either ambient air temperature or engine temperature, as desired. Refer to the full guide for optimal placement.
5. Initial Configuration: After power-up, configure basic settings such as wheel circumference for accurate speed/distance readings and desired temperature units (°F/°C).

For detailed, vehicle-specific installation instructions and wiring diagrams, please refer to the comprehensive guide available on the Trail Tech website or included with your product packaging.

Operating Instructions

The Trail Tech Striker features an intuitive interface with a main display and control buttons. The display shows various metrics, and the buttons allow you to navigate through modes and adjust settings.

Image: The Trail Tech Striker digital display unit. It shows various readings including speed (0.0 M/H), voltage (12.6V), temperature (106°F), time (12:35:16), and distance (14.05). Below the screen are three control buttons, with 'MODE' clearly visible in the center.

Display Overview:

• SPD (Speed): Displays current speed in M/H (miles per hour) or KM/H (kilometers per hour), depending on configuration.
• DST (Distance): Shows trip distance or odometer reading.
• Voltage (V): Indicates the vehicle's battery voltage. A low reading may suggest a charging system issue or a weak battery.
• Temperature (°F/°C): Displays the temperature from the connected sensor.
• Time: Current time of day.
• RT (Run Time): Accumulated engine run time.

Button Functions:

The Striker typically features three buttons: Left, Mode, and Right (or Up/Down arrows). Their functions may vary slightly depending on the current display mode.

• MODE Button: Press to cycle through different display modes (e.g., trip distance, odometer, maximum speed, average speed, etc.). Hold to enter settings menu.
• Left/Right Buttons (or Up/Down Arrows): Used for adjusting values in settings, resetting trip meters, or navigating sub-menus.

Consult the full user manual for specific button press sequences for advanced functions and settings adjustments.

Maintenance

The Trail Tech Striker is designed for durability and minimal maintenance. However, periodic checks can ensure its longevity and accurate performance.

• Cleaning: Wipe the display and unit housing with a soft, damp cloth. Avoid abrasive cleaners or solvents that could damage the screen or casing.
• Sensor Inspection: Periodically check the speed and temperature sensors for dirt, debris, or damage. Ensure the speed sensor magnet is securely attached and properly aligned.
• Wiring: Inspect all wiring connections for corrosion, fraying, or loose contacts. Secure any loose wires.
• Battery Voltage Monitoring: Regularly observe the voltage display. Consistent low readings may indicate an issue with your vehicle's battery or charging system, requiring attention.

Troubleshooting

If you encounter issues not listed here or require further assistance, please contact Trail Tech customer support.

Specifications

• Brand: Trail Tech
• Model: Striker (TRTE2308)
• Functions: Speed, 5 LED Group Backlight, Voltage, Distance, Temperature Sensor (Ambient/Engine), Odometer, Accumulated Run Time, Maintenance Reminder
• Compatibility: Yamaha GRIZZLY 550 4x4 (2009-2014)
• ASIN: B07F1YVSZ5
• First Available: June 26, 2018

Warranty and Support

Trail Tech products are manufactured to high standards. For information regarding product warranty, please refer to the warranty statement included with your product packaging or visit the official Trail Tech website.

For technical support, troubleshooting assistance, or to inquire about replacement parts, please contact Trail Tech customer service directly. Contact information can typically be found on their official website or in your product documentation.

Online resources, including detailed installation guides and FAQs, may also be available on the Trail Tech Store.