1. Introduction
This manual provides detailed instructions for the installation, operation, and maintenance of your PROFLO PFWO903 Waste and Overflow Push/Pull Stopper. Designed for durability and reliability, this stopper features a robust brass and zinc construction with a chrome finish, ensuring long-lasting performance and resistance to rust and corrosion in everyday use. Please read this manual thoroughly before beginning installation or use to ensure proper function and safety.
2. Important Safety Information
- Always turn off the main water supply to the fixture before attempting any plumbing work.
- Wear appropriate personal protective equipment, such as safety glasses and gloves, during installation.
- Ensure all connections are secure to prevent leaks.
- If you are unsure about any step, consult a qualified plumber.
- Keep small parts away from children.
3. Package Contents
Verify that all components are present before beginning installation.
- PROFLO PFWO903 Waste and Overflow Push/Pull Stopper Assembly (Chrome)
Image 1: The PROFLO PFWO903 Waste and Overflow Push/Pull Stopper in chrome finish. This image displays the complete stopper assembly, including the visible chrome cap and the internal brass mechanism.
4. Tools and Materials Required (Not Included)
- Plumber's Putty or Silicone Sealant
- Adjustable Wrench or Pliers
- Screwdriver (if removing existing drain components)
- Rags or Towels
5. Installation Guide
5.1. Before You Begin
- Ensure the bathtub drain opening is clean and free of debris.
- If replacing an existing stopper, carefully remove the old unit and clean any old sealant residue from the drain opening.
5.2. Step-by-Step Installation
- Prepare the Stopper: Apply a thin bead of plumber's putty or silicone sealant around the underside of the stopper's flange (the chrome rim that sits on the tub surface).
- Insert into Drain: Carefully insert the stopper assembly into the bathtub drain opening. Ensure the flange is centered and seated properly.
- Secure from Below: From underneath the bathtub, thread the drain shoe onto the stopper assembly. Hand-tighten first, then use an adjustable wrench or pliers to gently tighten until snug. Do not overtighten, as this can damage the tub or drain components.
- Wipe Excess Sealant: Wipe away any excess plumber's putty or silicone sealant that squeezes out from under the flange.
- Test for Leaks: Fill the bathtub with water and allow it to sit for a few minutes. Check underneath the tub for any signs of leaks around the drain connection. If leaks are detected, tighten the connection slightly or reapply sealant if necessary.
Image 2: A side view of the PROFLO PFWO903 Waste and Overflow Push/Pull Stopper, highlighting the brass stem and the chrome push/pull mechanism. This view helps in understanding the internal components during installation.
6. Operation
The PROFLO PFWO903 stopper operates with a simple push/pull mechanism:
- To Close the Drain: Push down on the stopper cap until it clicks or seats firmly, sealing the drain opening to retain water in the tub.
- To Open the Drain: Pull up on the stopper cap until it releases from its sealed position, allowing water to drain freely from the tub.
7. Care and Maintenance
To maintain the appearance and functionality of your PROFLO PFWO903 stopper:
- Cleaning: Clean regularly with a soft cloth and mild, non-abrasive soap. Rinse thoroughly with water and dry immediately.
- Avoid Harsh Chemicals: Do not use abrasive cleaners, scouring pads, or chemical solvents, as these can damage the chrome finish.
- Check for Debris: Periodically check the drain area for hair or debris that may accumulate around the stopper, which can affect its sealing ability or drainage.
8. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Stopper does not seal properly. | Debris under the stopper; worn gasket; improper installation. | Clean under the stopper. Check and replace gasket if worn. Re-check installation for proper seating and sealant. |
| Slow drainage when stopper is open. | Hair or debris accumulation in the drain pipe. | Remove the stopper and clear any obstructions from the drain pipe. Use a drain snake if necessary. |
| Stopper is difficult to push/pull. | Mineral buildup or lack of lubrication. | Clean the stopper mechanism. A small amount of silicone grease can be applied to moving parts if accessible and appropriate for plumbing. |
9. Product Specifications
| Brand | PROFLO |
| Model Number | PFWO903 |
| Material | Brass and Zinc |
| Finish | Chrome |
| Approximate Product Dimensions (L x W x H) | 1 x 1 x 1 inches |
| Item Weight | 3.84 ounces |
| UPC | 781889214626 |
10. Warranty Information
This PROFLO product is covered by a limited warranty. For specific details regarding warranty coverage, duration, and terms, please refer to the warranty documentation included with your purchase or contact PROFLO customer support directly. Proof of purchase may be required for warranty claims.
11. Customer Support
For further assistance, technical support, or to inquire about replacement parts, please contact PROFLO customer service. You can find additional resources and contact information by visiting the official PROFLO store on Amazon: