Suptig Diving Light User Manual

Introduction

Thank you for choosing the Suptig Diving Light. This high-power, dimmable, and waterproof LED video light is engineered to enhance your underwater photography and videography. Compatible with a wide range of action cameras, including GoPro Hero series, Dji Osmo, Insta360, and Akaso, this light provides essential illumination for capturing clear and vibrant footage in low-light or underwater environments. It is waterproof up to 147 feet (45 meters) and features multiple lighting modes to suit various conditions.

Setup

Package Contents

• Suptig Diving Light Unit
• Rechargeable Battery (1050mAh, compatible with GoPro Hero 3/3+ batteries)
• Micro USB Charging Cable
• Mounting Accessories (GoPro-style mount)

Figure 1: Suptig Diving Light and its accessories.

Battery Installation and Charging

1. Open the waterproof back cover of the light unit.
2. Insert the provided 1050mAh rechargeable battery into the battery compartment, ensuring correct polarity.
3. Close the waterproof back cover securely until it clicks into place. Ensure the seal is clean and free of debris.
4. To charge, connect the Micro USB charging cable to the Micro USB charging port on the light unit. The LED Battery Charge Indicator will show charging status.

A full charge provides approximately 1.5 hours of high-light operation, 4 hours of low-light operation, and 6 hours in SOS mode.

Figure 2: Rear view of the light, highlighting the battery and charging port.

Mounting the Light

The Suptig Diving Light comes with a standard GoPro-style mount, allowing for versatile attachment to various action camera accessories. It can be mounted directly to your GoPro housing or other compatible mounts. For use with SLR cameras, a Suptig cold shoe mount adapter (sold separately) is required.

Figure 3: The Suptig Diving Light attached to a GoPro camera.

Operating Instructions

Powering On/Off and Mode Selection

The light features a single button for power control and mode cycling. Press the button to cycle through the following modes:

• Normal (HI): Provides maximum brightness (500 Lumens Max, 5500K-6000K) for optimal illumination.
• Power Saving (LOW): Reduces brightness to conserve battery life.
• Flash (SOS): Emits a flashing signal for emergency situations or signaling.

To turn off the light, press and hold the button for a few seconds until the light extinguishes.

Underwater Use

The Suptig Diving Light is designed for reliable underwater performance, tested to be waterproof up to 147 feet (45 meters). Ensure the back cover is securely closed before any water exposure. This light is ideal for snorkeling, scuba diving, and other water activities, providing crucial light to enhance visibility and color in your underwater footage.

Figure 4: Enhancing underwater visibility with the Suptig Diving Light.

Figure 5: The light provides excellent illumination for capturing marine life.

Compatibility

The Suptig Diving Light offers broad compatibility with various action cameras and accessories. It is designed to work seamlessly with:

• GoPro Hero series (Hero 1, 2, 3, 3+, 4, 5, 5S, 6, 7, 8, 9, 10, 11, 12, 13)
• Dji Osmo Action cameras
• Insta360 cameras
• Akaso action cameras

For mounting on SLR cameras, a separate cold shoe mount adapter is required.

Figure 6: Broad compatibility with popular action cameras.

Maintenance

Waterproof Seal Care

• After each use, especially in saltwater, rinse the light thoroughly with fresh water.
• Inspect the O-ring seal on the back cover for any dirt, sand, or damage. Clean the O-ring and its groove with a soft, damp cloth.
• Apply a thin layer of silicone grease (not included) to the O-ring periodically to maintain its elasticity and waterproof integrity.
• Store the light in a cool, dry place when not in use.

Battery Care

• Avoid fully discharging the battery frequently to prolong its lifespan.
• If storing for extended periods, charge the battery to approximately 50% and recharge every 3-6 months.
• Use only the provided charging cable or a compatible Micro USB cable for charging.

Troubleshooting

Light Not Turning On

• Ensure the battery is correctly installed and fully charged.
• Check the battery contacts for any corrosion or debris.
• If the light still does not turn on, the battery may need replacement.

Water Leakage

• Immediately remove the light from water if leakage is suspected.
• Open the back cover and thoroughly dry the interior.
• Inspect the O-ring for any damage, cracks, or foreign particles. Replace if necessary.
• Ensure the back cover is closed tightly and correctly aligned before re-entering water.

Specifications

Warranty and Support

The Suptig Diving Light is backed by a 24-Month Warranty and a 30 Days Money Back Guarantee. For any product inquiries, technical support, or warranty claims, please contact Suptig customer service through the official channels.

You can also visit the Suptig Store on Amazon for more information and to explore other products.