1. Introduction
This manual provides detailed instructions for the safe installation, operation, and maintenance of your Access Lighting Bayside Collection LED Wall Fixture, model 20032LEDMG-SAT/FST. Please read this manual thoroughly before installation and retain it for future reference.
Figure 1: Access Lighting Bayside Collection LED Wall Fixture (Satin Finish). This image displays the modern, rectangular design of the wall fixture with its integrated LED light source at the bottom, showcasing its sleek appearance.
2. Safety Information
WARNING: Risk of electric shock. Disconnect power at the fuse box or circuit breaker before installation or servicing.
- All electrical connections must be in accordance with local codes and ordinances, and the National Electric Code (NEC).
- Consult a qualified electrician if you are unsure about the installation process.
- Ensure the fixture is properly grounded.
- Do not install this fixture on a wet surface.
- This product is designed for outdoor use and is water resistant. However, avoid direct high-pressure water spray.
3. Package Contents
Verify that all components are present before beginning installation:
- LED Wall Fixture (Model 20032LEDMG-SAT/FST)
- Mounting Hardware Kit (screws, wire nuts, mounting plate)
- Remote Control
- Instruction Manual
4. Setup (Installation)
This fixture is designed for surface mount installation on a wall. Professional installation is recommended.
- Prepare for Installation: Turn off power at the circuit breaker or fuse box to avoid electrical shock. Ensure the power is completely off before proceeding.
- Mounting Plate Installation: Attach the mounting plate to the junction box on the wall using the provided screws. Ensure the plate is securely fastened.
- Wiring Connections:
- Connect the black wire from the fixture to the black (Live) wire from the junction box using a wire nut.
- Connect the white wire from the fixture to the white (Neutral) wire from the junction box using a wire nut.
- Connect the green or bare copper ground wire from the fixture to the ground wire from the junction box and to the mounting plate using a ground screw.
- Carefully tuck all wires into the junction box.
- Secure the Fixture: Align the fixture with the mounting plate and secure it using the provided screws. Ensure the fixture is flush against the wall and stable.
- Restore Power: Once the fixture is securely installed and all connections are checked, restore power at the circuit breaker.
Figure 2: Fixture Dimensions. This image illustrates the physical dimensions of the wall fixture, showing a length of 4.5 inches, a width of 5.5 inches, and a height of 8 inches.
5. Operating Instructions
This LED wall fixture is controlled via a remote control.
- Power On/Off: Use the Power button on the remote control to turn the fixture on or off.
- Light Control: The fixture provides warm white light. Use the remote control to adjust brightness levels if applicable to your specific remote model. Refer to your remote control's specific instructions for advanced features.
6. Maintenance
The Access Lighting LED Wall Fixture requires minimal maintenance.
- Cleaning: To clean the fixture, ensure power is off. Wipe with a soft, damp cloth. Do not use abrasive cleaners or solvents, as these may damage the finish or electrical components.
- LED Lifespan: The integrated LED light source is designed for long-term use and does not require bulb replacement.
- Inspection: Periodically inspect the fixture for any signs of damage or loose connections.
7. Troubleshooting
If you encounter issues with your fixture, refer to the following common problems and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Fixture does not light up. | No power supply. Loose wiring connection. Faulty remote control. | Check circuit breaker. Ensure all wire connections are secure (power off first). Replace remote control batteries or ensure line of sight. |
| Remote control not working. | Dead batteries. Obstruction between remote and fixture. | Replace batteries in the remote control. Ensure clear path between remote and fixture. |
| Light flickers or dims unexpectedly. | Unstable power supply. Loose wiring. | Consult an electrician to check power supply. Check all wiring connections (power off first). |
If the problem persists after attempting these solutions, contact customer support.
8. Specifications
| Feature | Detail |
|---|---|
| Brand | Access Lighting |
| Model Number | 20032LEDMG-SAT/FST |
| Material | Aluminum (Fixture), Glass (Shade) |
| Finish | Satin |
| Light Source | Integrated LED |
| Light Color | Warm White |
| Brightness | 590 Lumens |
| Wattage | 15 Watts |
| Voltage | 120 Volts |
| Control Method | Remote Control |
| Indoor/Outdoor Usage | Outdoor |
| Water Resistance Level | Water Resistant |
| Dimensions (L x W x H) | 4.5" x 5.5" x 8" |
| Item Weight | 4.3 Pounds |
| Installation Type | Surface Mount |
| Required Assembly | Yes |
9. Warranty Information
This Access Lighting fixture is covered by a 1-year manufacturer's warranty from the date of purchase. This warranty covers defects in materials and workmanship under normal use. It does not cover damage resulting from improper installation, accident, misuse, abuse, or unauthorized modifications. Please retain your proof of purchase for warranty claims.
10. Support
For technical assistance, replacement parts, or warranty inquiries, please contact Access Lighting customer support. You may also visit the official Access Lighting Store on Amazon for more information.
