360 Lighting Burke Industrial Modern Wall Sconce

Introduction

This manual provides detailed instructions for the safe installation, operation, and maintenance of your 360 Lighting Burke Industrial Modern Wall Sconce. Please read all instructions carefully before beginning installation and retain this manual for future reference.

Safety Information

WARNING: RISK OF ELECTRIC SHOCK.

• Always turn off the main power supply at the circuit breaker before installing, servicing, or changing any part of the fixture.
• Consult a qualified electrician if you are unsure about the installation process.
• Ensure all electrical connections are made in accordance with local codes and ordinances.
• Do not exceed the maximum wattage specified for the bulb.
• This fixture is designed for indoor use only and is not water resistant.

Package Contents

Verify that all components are present before beginning installation:

• Wall Sconce Fixture (1)
• Clear Glass Cone Shade (1)
• LED Edison-style Bulb (1)
• Mounting Hardware (screws, wire nuts)

Setup and Installation

Follow these steps to install your wall sconce:

1. Prepare for Installation: Turn off power at the circuit breaker. Ensure the mounting surface is clean and dry.
2. Mount the Fixture: Secure the backplate to the wall junction box using the provided mounting hardware. The fixture is designed for wall mount installation.
3. Connect Wiring: Connect the fixture's wires to the household electrical wires according to standard electrical practices (black to black, white to white, ground to ground). Use wire nuts to secure connections.
4. Install the Glass Shade: The clear glass cone shade is secured by small pins. Unscrew these pins, carefully place the glass shade over the bulb socket, and then re-tighten the pins to hold the shade in place. The shade can be installed with the glass facing up or down.
5. Insert the Bulb: Screw the included LED Edison-style bulb into the socket. Ensure the bulb is fully seated. The fixture supports a maximum 60-watt bulb.
6. Restore Power: Once installation is complete, turn the power back on at the circuit breaker.

Figure 1: Product Dimensions. The sconce measures 10 3/4 inches high, with a 5 1/4 inch wide backplate, extending 8 3/4 inches from the wall. The glass shade is 7 1/4 inches wide and 5 1/2 inches high.

Figure 2: Sconce Detail. A close-up of the sconce showing the dark bronze backplate, brass arm, and clear glass shade with the bulb inside.

Figure 3: Bulb and Shade. A detailed view of the LED Edison-style bulb within the clear glass cone shade, illustrating the filament design.

Operating Instructions

The 360 Lighting Burke Wall Sconce is designed for simple operation:

• Power On/Off: Operate the light using your existing wall switch. The fixture is hardwired and controlled by the wall switch it is connected to.
• Dimmable Functionality: This fixture is dimmable. To utilize this feature, ensure you have a compatible dimmer switch installed and are using a dimmable LED bulb.
• Light Output: The included 7-watt LED bulb provides 800 lumens of 2200K amber light, comparable to a 60-watt incandescent bulb.

Figure 4: Included Bulb. The LED Edison-style bulb that comes with the fixture, featuring a clear glass casing and visible filaments.

Maintenance

Regular maintenance ensures the longevity and appearance of your wall sconce:

• Cleaning the Glass Shade: To clean the clear glass cone shade, carefully unscrew the retaining pins and remove the shade. Wash with mild soap and water, or a glass cleaner. Dry thoroughly before reattaching.
• Cleaning Metal Parts: Wipe metal surfaces with a soft, dry cloth. Avoid abrasive cleaners or polishes that could damage the finish.
• Bulb Replacement: Ensure power is off at the circuit breaker. Carefully unscrew the old bulb and replace it with a new LED bulb (E26 base, maximum 60 watts).

Troubleshooting

If you encounter issues with your wall sconce, refer to the following common problems and solutions:

• Light does not turn on:
  • Check the circuit breaker to ensure power is on.
  • Verify the bulb is screwed in correctly and is not burnt out.
  • Ensure all wire connections are secure.
• Light flickers or dims unexpectedly:
  • Confirm the bulb is fully seated in the socket.
  • If using a dimmer, ensure it is compatible with LED bulbs.
  • Check for loose wiring connections.

If problems persist, contact a qualified electrician or the manufacturer for assistance.

Specifications

Warranty and Support

For warranty information or technical support, please refer to the product packaging or contact 360 Lighting customer service. Keep your purchase receipt for warranty claims.