1. Introduction
Thank you for choosing the AIKE AK2630T Automatic Jet Hand Dryer. This manual provides essential information for the safe installation, operation, and maintenance of your new hand dryer. Please read it thoroughly before use and retain it for future reference.
The AIKE AK2630T is a high-performance, automatic jet hand dryer designed for efficiency and hygiene. Key features include:
- Powerful Drying: Operates at 120V, 1400W, with an air velocity of 105 m/s, ensuring quick hand drying.
- Intelligent Heating: An auto temperature controller adjusts heating based on ambient environmental temperature, indicated by an LED.
- Extreme Sanitation: Features a drain tank with a visible level window to collect excess water, keeping the surrounding area clean. The filter is removable and washable for easy maintenance.
- Durable Construction: Expertly crafted from ABS polycarbonate material, providing long-lasting strength, corrosion resistance, and durability for extensive use.
2. Safety Instructions
WARNING: To reduce the risk of electric shock, fire, or injury, read all instructions before installing or using this appliance.
- Ensure the power supply matches the voltage specified on the product label (120V).
- Installation must be performed by a qualified electrician in accordance with all local and national electrical codes.
- Do not install the hand dryer near flammable materials or in areas with excessive moisture.
- Disconnect power before performing any maintenance or cleaning.
- Do not insert foreign objects into the air outlet or inlet.
- This appliance is not intended for use by persons (including children) with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
- Keep children away from the hand dryer.
3. Package Contents
Please check the package contents upon unpacking. If any items are missing or damaged, contact your retailer.
- AIKE AK2630T Automatic Jet Hand Dryer Unit
- Mounting Hardware (screws, wall anchors)
- User Manual
4. Setup & Installation
The AIKE AK2630T hand dryer is designed for wall mounting. Ensure the installation location is suitable for electrical connections and provides adequate space for use.
4.1. Recommended Mounting Height
- For adults: Approximately 40-45 inches (100-115 cm) from the floor to the bottom of the unit.
- For children/ADA compliance: Adjust height as necessary.
4.2. Installation Steps
- Prepare the Wall: Choose a sturdy wall location. Mark the drilling points for the mounting bracket using the provided template (if included) or by measuring the unit's mounting holes.
- Drill Holes: Drill holes at the marked points. Insert wall anchors if mounting into drywall.
- Mount the Bracket/Unit: Secure the mounting bracket (if separate) or the hand dryer directly to the wall using the provided screws. Ensure it is level and firmly attached.
- Electrical Connection: Connect the hand dryer to a dedicated 120V, 50Hz electrical circuit. This connection should be hardwired by a qualified electrician. Ensure proper grounding. The unit comes with a 66-inch power cord for hardwiring.
- Secure the Unit: If using a separate mounting bracket, attach the hand dryer unit to the bracket and secure it with any locking screws.
Figure 1: AIKE AK2630T Hand Dryer with key dimensions (18.50" H x 9.84" W x 6.49" D) and 66" power cord.
Figure 2: Front view of the AIKE AK2630T Hand Dryer, showing the power and check indicators, and hand sensor area.
5. Operating Instructions
The AIKE AK2630T hand dryer is fully automatic and sensor-activated.
- Power On: Once installed and connected to power, the hand dryer is in standby mode. The "POWER" indicator (red LED) will illuminate.
- Activate: Place your hands into the drying chamber from the bottom opening. The infrared sensor will detect your hands.
- Drying Cycle: The powerful air jets will activate automatically, drying your hands quickly. The intelligent heating system will adjust the air temperature based on the room's ambient temperature.
- Stop: Remove your hands from the drying chamber. The air jets will stop automatically.
The "CHECK" indicator (green LED) will illuminate if there is an issue requiring attention, such as a full drain tank or a blocked filter.
6. Maintenance
Regular maintenance ensures optimal performance and hygiene of your hand dryer.
6.1. Cleaning the Exterior
- Frequency: As needed, or at least weekly in high-traffic areas.
- Procedure: Disconnect power to the unit. Wipe the exterior surface with a soft, damp cloth and a mild, non-abrasive cleaner. Do not use harsh chemicals or abrasive pads.
6.2. Emptying and Cleaning the Drain Tank
The drain tank collects excess water to prevent drips on the floor. Monitor the level window. When the "CHECK" indicator illuminates, the drain tank likely needs emptying.
- Frequency: As indicated by the level window or "CHECK" light, or at least monthly.
- Procedure:
- Disconnect power to the hand dryer.
- Locate the drain tank at the bottom of the unit.
- Carefully slide out the drain tank.
- Empty the collected water and clean the tank with soap and water. Rinse thoroughly.
- Ensure the tank is dry before reinserting it into the unit.
- Reconnect power.
Figure 3: Close-up view of the removable drain tank at the base of the hand dryer.
6.3. Cleaning the Air Filter
The removable and washable filter helps maintain air quality and unit efficiency.
- Frequency: Every 1-3 months, depending on usage and environment, or if the "CHECK" indicator illuminates.
- Procedure:
- Disconnect power to the hand dryer.
- Locate the air filter (usually near the air intake).
- Remove the filter.
- Clean the filter by rinsing it under running water or using a vacuum cleaner to remove dust and debris.
- Allow the filter to air dry completely before reinserting it.
- Reconnect power.
7. Troubleshooting
If you encounter issues with your AIKE AK2630T hand dryer, refer to the table below for common problems and solutions.
| Problem | Possible Cause | Solution |
|---|---|---|
| Hand dryer does not turn on. | No power supply. Circuit breaker tripped. | Check power connection. Reset circuit breaker. Ensure proper installation. |
| Air flow is weak or inconsistent. | Blocked air filter. Obstruction in air inlet/outlet. | Clean or replace the air filter. Remove any obstructions. |
| Hand dryer runs continuously or does not stop. | Sensor obstruction or malfunction. | Clean the sensor lens. Ensure no objects are continuously in the sensor's field of view. If problem persists, contact support. |
| "CHECK" indicator light is on. | Drain tank full. Air filter blocked. | Empty and clean the drain tank. Clean or replace the air filter. |
| Water drips from the unit. | Drain tank full or improperly seated. | Empty and properly re-seat the drain tank. |
8. Specifications
| Feature | Detail |
|---|---|
| Model Number | AK2630T |
| Voltage | 120V |
| Power | 1400W |
| Frequency | 50Hz |
| Air Velocity | 105 m/s |
| Noise Level | 76dB |
| Material | ABS Polycarbonate |
| Color | Silver |
| Product Dimensions (H x W x D) | 18.50 x 9.84 x 6.49 inches (470 x 250 x 165 mm) |
| Item Weight | 9.7 pounds |
| Manufacturer | Zhejiang AIKE Appliances Co., Ltd. |
9. Warranty & Support
9.1. Product Warranty
AIKE offers a 2-year worry-free replacement guarantee for this product. This warranty covers manufacturing defects and non-human damage. In the event of a covered issue, AIKE will provide new parts or service free of charge.
Please retain your proof of purchase for warranty claims.
9.2. Customer Support
For technical assistance, warranty claims, or any questions regarding your AIKE AK2630T hand dryer, please contact AIKE customer service through your retailer or the official AIKE website.
When contacting support, please have your model number (AK2630T) and purchase date available.
