1. Introduction
This instruction manual provides essential information for the safe and effective use of your LKPower AC Adapter. This adapter is designed to provide reliable power to your Uniden Bearcat BC60XLT and BC60XLT-1 radio scanners, allowing operation from standard electrical outlets or charging the device's battery.
Please read this manual thoroughly before using the product and retain it for future reference.
2. Safety Information
- Indoor Use Only: This adapter is designed for indoor use in dry locations. Do not expose to rain, moisture, or extreme temperatures.
- Proper Voltage: Ensure the wall outlet voltage matches the adapter's input specifications (AC 100-240V).
- Over Voltage Protection: The adapter incorporates over voltage protection to safeguard your device.
- Over Heat Protection: The adapter is designed with over heat protection. If it becomes excessively hot, disconnect it immediately.
- Avoid Damage: Do not use the adapter if the cord or plug is damaged. Do not attempt to open or repair the adapter.
- Unplug When Not in Use: Disconnect the adapter from the power outlet when not in use for extended periods.
- Keep Away from Children: Store the adapter out of reach of children.
3. Package Contents
Verify that all items are present in the package:
- 1 x LKPower AC Adapter
Image: Front and side view of the LKPower AC Adapter, showing the two-prong plug and the adapter body.
4. Setup
- Connect to Device: Insert the barrel connector end of the AC adapter cable into the power input port of your Uniden Bearcat BC60XLT or BC60XLT-1 radio scanner.
- Connect to Power Outlet: Plug the two-prong AC plug of the adapter into a standard electrical wall outlet (AC 100-240V, 50/60Hz).
- Verify Connection: Ensure both connections are secure. The scanner should now receive power or begin charging its battery.
Image: The LKPower AC Adapter plugged into a white power strip, illustrating a typical setup for powering a device.
5. Operating Instructions
Once properly connected, the LKPower AC Adapter will supply continuous power to your Uniden Bearcat BC60XLT or BC60XLT-1 radio scanner. If your scanner has a rechargeable battery, the adapter will also facilitate battery charging. Refer to your scanner's specific user manual for details on its power indicator lights and charging status.
Image: The LKPower AC Adapter with its cable coiled, showing the overall design and connector type.
6. Maintenance
- Cleaning: Disconnect the adapter from the power outlet and your device before cleaning. Use a soft, dry cloth to wipe the exterior. Do not use liquid cleaners or solvents.
- Storage: When not in use, store the adapter in a cool, dry place, away from direct sunlight and extreme temperatures. Avoid tightly coiling the cable to prevent damage.
- Inspection: Periodically inspect the adapter and cable for any signs of wear or damage. If damage is observed, discontinue use and replace the adapter.
7. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Device not powering on/charging |
|
|
| Adapter feels excessively hot |
|
|
8. Specifications
- Model Number: 180116453
- Input: AC 100-240V, 50/60Hz
- Wattage: 36.5 watts
- Compatible Devices: Uniden Bearcat BC60XLT, Uniden Bearcat BC60XLT-1 Radio Scanners
- Connector Type: Barrel connector
- Item Weight: 4 ounces (approx. 113 grams)
- Package Dimensions: 4 x 3 x 1.5 inches (approx. 10.16 x 7.62 x 3.81 cm)
- Cable Length: Approximately 76 inches (approx. 193 cm)
Image: The LKPower AC Adapter with key dimensions (1.6 inch, 2.6 inch, 1.2 inch) and cable length (76 inch) clearly labeled.
9. Warranty and Support
For warranty information and customer support, please refer to the documentation included with your purchase or contact the seller directly. Specific warranty terms may vary.
Brand: LKPower