UpStart Components ALB-8009-2PK-DL9502

Instruction Manual

Product: 2-Pack Replacement Light Bulb for General Electric HTS18GBSARWW - Compatible General Electric 8009 Light Bulb

Brand: UpStart Components

Model: ALB-8009-2PK-DL9502

Product Overview

This manual provides essential information for the safe and effective use of your UpStart Components Replacement Light Bulbs. These bulbs are designed as a compatible replacement for General Electric HTS18GBSARWW and 8009 Light Bulbs, offering reliable illumination for your appliances.

Two UpStart Components replacement light bulbs side by side, showing their clear glass and brass bases.

Figure 1: Two UpStart Components Replacement Light Bulbs.

Setup and Installation

Before installing the replacement light bulb, ensure the power to the fixture is turned off at the circuit breaker to prevent electrical shock. Allow the old bulb to cool completely before handling.

Safety First: Disconnect power to the light fixture or appliance. If replacing a hot bulb, wait for it to cool down.
Remove Old Bulb: Carefully unscrew the old light bulb by turning it counter-clockwise. Dispose of the old bulb responsibly.
Inspect Socket: Check the light socket for any debris or damage. Ensure it is clean and dry before installing the new bulb.
Install New Bulb: Gently screw the new UpStart Components replacement bulb into the socket by turning it clockwise until it is snug. Do not overtighten.
Restore Power: Once the new bulb is securely in place, restore power to the fixture or appliance.

A single UpStart Components replacement light bulb shown at an angle, highlighting its clear glass and threaded brass base.

Figure 2: Angled view of the replacement light bulb, showing the E26 base.

Operating Instructions

These replacement light bulbs operate like standard incandescent bulbs. Once installed and power is restored, simply use the fixture's or appliance's switch to turn the light on or off.

Power On: Activate the light switch or power control for the fixture.
Power Off: Deactivate the light switch or power control to turn off the light.

Maintenance

These light bulbs require minimal maintenance. For optimal performance and longevity, consider the following:

Cleaning: If the bulb becomes dusty, ensure the power is off and the bulb is cool. Gently wipe the glass with a soft, dry cloth. Do not use liquid cleaners directly on the bulb.
Replacement: Replace the bulb when it burns out. The lifespan of the bulb can vary based on usage and environmental factors.

Troubleshooting

If your replacement light bulb is not functioning as expected, consider the following common issues and solutions:

Problem	Possible Cause	Solution
Bulb does not light up.	No power to the fixture. Bulb not screwed in properly. Bulb is faulty. Fixture socket is faulty.	Check circuit breaker or wall switch. Ensure bulb is securely tightened in the socket. Try the bulb in another working fixture. Test the fixture with a known working bulb.
Bulb flickers.	Loose connection in the socket. Incompatible dimmer switch.	Ensure bulb is securely tightened. These are incandescent bulbs; ensure your dimmer is compatible with incandescent loads.

Specifications

Detailed technical specifications for the UpStart Components Replacement Light Bulb:

Attribute	Value
Brand	UpStart Components
Model Number	ALB-8009-2PK-DL9502
Special Feature	Long Lasting
Wattage	40 watts
Bulb Shape Size	A15
Bulb Base	E26
Voltage	120 Volts
Unit Count	2.0 Count
Number of Items	2
Shape	A15
Material	Glass
Light Source Wattage	40 Watts
Control Method	App (Note: This bulb is a simple incandescent bulb; "App Control" may refer to a compatible smart fixture, not the bulb itself.)
Product Dimensions	1.9 x 3.8 x 3.22 inches
Date First Available	September 1, 2017

The base of a single UpStart Components replacement light bulb, showing the E26 screw-in base and the contact point.

Figure 3: Close-up view of the E26 bulb base.

Warranty Information

As stated by the manufacturer, any warranties for this product are offered solely by UpStart Components. This product is a replacement part and is not covered under any warranties offered by the original equipment manufacturers (OEMs) of the appliances it is compatible with. For specific warranty terms and conditions, please refer to the documentation provided by UpStart Components or contact their customer support.

Customer Support

For further assistance, technical support, or inquiries regarding your UpStart Components Replacement Light Bulbs, please contact the manufacturer directly. Refer to the product packaging or the UpStart Components official website for contact details.