Introduction
This manual provides instructions for the safe and efficient use of your B.K.Licht LED Dimmable Touch Control Table Lamp, Model BKL1088. This lamp features a modern design with an opal white glass shade and a metal base, offering three levels of dimmable light via touch control. It is designed for indoor use with an E14 bulb (not included).
Figure 1: B.K.Licht LED Dimmable Touch Control Table Lamp (Tulip variant)
Safety Instructions
- Read all instructions carefully before assembly and use.
- Ensure the power supply is disconnected before installation, cleaning, or bulb replacement.
- This product is designed for indoor use only. Do not expose to moisture or extreme temperatures.
- Use only dimmable E14 bulbs with a maximum wattage of 40W. Non-dimmable bulbs may cause malfunction or damage.
- Do not attempt to modify or repair the lamp. Contact qualified personnel for service.
- Keep out of reach of children and pets.
- Place the lamp on a stable, flat surface to prevent tipping.
Package Contents
Verify that all components are present and undamaged upon unpacking:
- 1 x B.K.Licht LED Dimmable Touch Control Table Lamp (Model BKL1088)
- 1 x Power Cable (1.4 meters)
- Note: E14 bulb is not included and must be purchased separately.
Setup and Installation
- Unpack the Lamp: Carefully remove all packaging materials.
- Install the Bulb:
- Ensure the lamp is unplugged from the power outlet.
- Gently unscrew the glass shade from the lamp base.
- Screw a dimmable E14 bulb (max 40W) into the lamp holder. Do not overtighten.
- Carefully reattach the glass shade to the lamp base.
- Position the Lamp: Place the lamp on a stable, flat surface in your desired indoor location. The 1.4-meter cable allows for flexible placement.
- Connect to Power: Plug the power cable into a standard 230V electrical outlet.
Figure 2: Lamp placed on a bedside table, demonstrating typical setup.
Operating Instructions
The B.K.Licht table lamp features a convenient touch control function for switching on/off and adjusting brightness levels.
- Switching On/Off: Lightly touch any metal part of the lamp base to turn the lamp on or off.
- Adjusting Brightness:
- With the lamp on, touch the metal base again to cycle through the three brightness levels: 30%, 70%, and 100%.
- A fourth touch will turn the lamp off.
Figure 3: Demonstrating touch control on the lamp base.
Figure 4: Brightness levels (30%, 70%, 100%) controlled by touch.
Maintenance
- Cleaning:
- Always unplug the lamp before cleaning.
- Wipe the metal base with a soft, dry cloth.
- Clean the glass shade with a soft, damp cloth and mild detergent if necessary, then dry thoroughly. Avoid abrasive cleaners.
- Bulb Replacement:
- Ensure the lamp is unplugged and the bulb has cooled down.
- Gently unscrew the glass shade.
- Unscrew the old E14 bulb and replace it with a new dimmable E14 bulb (max 40W).
- Reattach the glass shade.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Lamp does not turn on. |
|
|
| Dimming function does not work. |
|
|
| Lamp flickers or buzzes. |
|
|
Specifications
Figure 5: Product Dimensions.
| Feature | Detail |
|---|---|
| Model Number | BKL1088 |
| Brand | B.K.Licht |
| Product Dimensions (D x H) | 11D x 20H cm (108mm diameter x 195mm height) |
| Base Material | Metal |
| Shade Material | Glass (Opal White) |
| Finish Type | Matte |
| Bulb Base | E14 |
| Recommended Bulb Type | Dimmable LED E14 |
| Max. Wattage | 40W |
| Power Source | Corded Electric |
| Voltage | 230V |
| Cable Length | 1.4 meters |
| Control Method | Touch Control (3-step dimming) |
| IP Rating | IP20 (Indoor Use Only) |
| Style | Modern |
| Recommended Room Type | Bedroom |
Warranty and Support
For warranty information or technical support, please refer to the retailer's policy or contact B.K.Licht customer service directly. Keep your proof of purchase for any warranty claims.
Contact information for B.K.Licht can typically be found on their official website or through your point of purchase.