Introduction
Thank you for choosing the Taylor Dual Event Digital Timer with Clock. This versatile timer is designed to simplify your multitasking needs in the kitchen and beyond, allowing you to track two separate events simultaneously. This manual provides detailed instructions for setup, operation, maintenance, and troubleshooting to ensure optimal performance of your device.
Key features include:
- Simultaneous timing of two events with unique alarm rings.
- Count-up function after alarm sounds to indicate elapsed time.
- Digital clock and calendar display when not in timer mode.
- Built-in stand and magnetic back for versatile placement.
- Includes one LR44 battery.
Product Overview
Familiarize yourself with the components of your Taylor Dual Event Digital Timer.
Figure 1: Front view of the Taylor Dual Event Digital Timer. The display shows two timer readouts, and buttons for 'TIMER 1', 'TIMER 2', 'HR/+', 'MIN/-', 'Play/Pause', 'Stop', and 'ENTER' are visible below.
Figure 2: Side view of the timer, illustrating the integrated kickstand for tabletop use.
Figure 3: Back view of the timer, highlighting the strong magnet for attachment to metal surfaces and the battery compartment cover.
Setup
Battery Installation
Your timer requires one LR44 button cell battery, which is included and pre-installed. If replacement is needed:
- Locate the battery compartment on the back of the timer.
- Slide the battery compartment cover downwards to open.
- Insert one new LR44 battery, ensuring the positive (+) side faces upwards.
- Replace the battery compartment cover, sliding it upwards until it clicks into place.
Figure 4: Battery compartment with the cover removed, showing the LR44 battery slot.
WARNING: Ingestion Hazard. This product contains a button cell or coin battery. If swallowed, it can cause severe injury or death in just 2 hours. Seek immediate medical attention.
Figure 5: Button cell battery warning.
Initial Clock Setting
To set the current time and date:
- Locate the slide switch on the back of the timer, labeled 'CLOCK' and 'TIMER'. Slide it to the 'CLOCK' position.
- The display will show the current time and date.
- Press and hold the 'HR/+' button to set the hour.
- Press and hold the 'MIN/-' button to set the minutes.
- Press the 'ENTER' button to confirm the time.
- Use the 'HR/+' and 'MIN/-' buttons to set the month, day, and year, pressing 'ENTER' after each setting.
Operating Instructions
Switching Modes
To switch between clock mode and timer mode, use the slide switch on the back of the unit. Slide it to 'TIMER' for timer functions and 'CLOCK' for time and date display.
Setting Timers (Timer 1 and Timer 2)
The timer allows you to set two independent countdown timers, each up to 23 hours and 59 minutes.
- Ensure the mode switch on the back is set to 'TIMER'.
- Press either the 'TIMER 1' or 'TIMER 2' button to select the desired timer. The selected timer's display will flash.
- Use the 'HR/+' button to set the hours.
- Use the 'MIN/-' button to set the minutes.
- Press the 'ENTER' button to confirm the set time. The display will stop flashing.
Starting and Stopping Timers
- After setting a timer, press the 'Play/Pause' button (triangle icon) to start the countdown.
- To pause a running timer, press the 'Play/Pause' button again. Press it once more to resume.
- To stop a timer and clear its setting, press the 'Stop' button (square icon).
Alarm Function
When a timer counts down to zero, a unique alarm will sound for that specific timer (Timer 1 or Timer 2). The display will also flash, and the timer will begin counting up, indicating how much time has elapsed since the alarm first sounded. This feature is useful for knowing how long an item has been ready.
To silence the alarm, press any button. The count-up display will continue until the timer is reset or cleared.
Resetting Timers
To quickly reset a timer to zero after it has completed or been stopped, press the 'RESET' button located below the 'HR/+' and 'MIN/-' buttons. This will clear the current timer setting and stop any count-up function.
Maintenance
Cleaning
To clean your timer, wipe it with a soft, damp cloth. Do not use abrasive cleaners or immerse the unit in water. Ensure the unit is completely dry before storage or next use.
Battery Replacement
When the display becomes dim or the timer functions erratically, it is time to replace the LR44 battery. Follow the battery installation steps outlined in the Setup section.
Storage
Store the timer in a cool, dry place when not in use. If storing for an extended period, it is recommended to remove the battery to prevent leakage.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Display is blank or dim. | Battery is low or depleted. | Replace the LR44 battery. |
| Timer not counting down. | Timer not started or paused. | Press the 'Play/Pause' button to start. Ensure a time has been set. |
| Alarm does not stop. | No button pressed to silence alarm. | Press any button to silence the alarm. The count-up will continue until reset. |
| Timer resets unexpectedly or shows incorrect time/date. | Battery connection issue or very low battery. | Check battery installation. Replace battery if necessary. Re-set time/date. |
| Difficulty setting time or operating buttons. | Incorrect mode selected. | Ensure the slide switch on the back is in the correct 'TIMER' or 'CLOCK' position. |
Specifications
- Model Number: 5880
- Color: White
- Material: Stainless Steel (internal components)
- Product Dimensions: 0.75"D x 3.38"W x 3.38"H
- Item Weight: 1.6 ounces
- Number of Settings: 3 (Clock, Timer 1, Timer 2)
- Battery: 1 x LR44 (included)
- Country of Origin: China
- UPC: 077784029701
Warranty and Support
Taylor products are manufactured to high-quality standards. For warranty information or technical support, please refer to the packaging or visit the official Taylor website. Keep your purchase receipt as proof of purchase.
For further assistance, you may contact Taylor customer service directly. Contact information is typically available on the manufacturer's website or product packaging.
