Sun Joe GTS4002C Cordless Lawn Care System User Manual

Introduction

The Sun Joe GTS4002C is a versatile 3-in-1 24V cordless lawn care system designed to assist with various yard maintenance tasks. This system features three interchangeable tool heads: a pole saw, a hedge trimmer, and a string trimmer, along with a 5.3-foot extension pole. It is powered by a lightweight 24-Volt battery pack, offering portability and convenience for use in areas where power outlets are not readily available. This manual provides essential information for the safe and effective operation, maintenance, and troubleshooting of your Sun Joe GTS4002C system.

Important Safety Information

WARNING: Proposition 65 Warning. This product can expose you to chemicals including lead and lead compounds, which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.

Always read and understand all safety warnings, instructions, illustrations, and specifications provided with this power tool. Failure to follow all instructions listed below may result in electric shock, fire, and/or serious injury.

• Personal Protective Equipment (PPE): Always wear appropriate eye protection (safety glasses), hearing protection, and heavy-duty gloves when operating the tool. Long pants and sturdy, non-slip footwear are also recommended.
• Work Area Safety: Keep the work area clean and well-lit. Cluttered or dark areas invite accidents. Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust.
• Electrical Safety: Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges, and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
• Tool Use and Care: Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.
• Battery Pack Safety: Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack.
• Maintenance: Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.

Package Contents

Upon unpacking your Sun Joe GTS4002C system, ensure all items are present and undamaged. The package typically includes:

• Main Power Handle with Extension Pole
• Pole Saw Attachment (8-inch bar and chain)
• Hedge Trimmer Attachment (17.7-inch blade)
• String Trimmer Attachment (10-inch cutting diameter)
• 2.0-Ah Lithium-Ion Battery
• Battery Charger
• Blade Cover for Hedge Trimmer
• Chain Scabbard for Pole Saw
• Operator's Manual (this document)

Figure 1: Overview of the Sun Joe GTS4002C system components, including the main power handle with extension pole, pole saw, hedge trimmer, and string trimmer attachments.

Setup

1. Battery Charging

Before first use, fully charge the 24V lithium-ion battery. Connect the charger to a standard electrical outlet and then connect the battery to the charger. The charging indicator light on the charger will indicate the charging status. A full charge typically takes approximately one hour.

2. Attaching Tool Heads and Extension Pole

The Sun Joe GTS4002C features a quick-connect system for interchanging tool heads. Ensure the battery is removed before attaching or detaching any components.

• Connecting the Extension Pole: Align the male end of the extension pole with the female receptacle on the main power handle. Push firmly until it clicks into place. Ensure the locking mechanism is engaged.
• Attaching Tool Heads: Select the desired tool head (pole saw, hedge trimmer, or string trimmer). Align the connection point of the tool head with the end of the extension pole (or directly to the power handle if not using the extension). Push and twist until it locks securely. Verify the connection is firm before operation.

Figure 2: The multi-angle head feature allows for versatile positioning of the pole saw or hedge trimmer for various cutting tasks.

Operating Instructions

Always ensure the battery is fully charged and securely inserted into the power handle before operation. Wear all recommended PPE.

1. General Operation

• To start the tool, press and hold the safety lock-off button, then squeeze the trigger switch.
• To stop the tool, release the trigger switch.
• The 5.3-foot extension pole allows for extended reach, enabling you to trim high hedges or saw overhead limbs safely from the ground.

Figure 3: Demonstrates the extended reach capability of the Sun Joe system, allowing users to access higher branches.

2. Pole Saw Operation

The 8-inch pole saw is designed for cutting branches and limbs. It can cut through trunks, limbs, logs, and branches up to 7.5 inches wide.

• Ensure the chain is properly tensioned and lubricated with bar and chain oil before each use.
• Position the saw blade against the branch, ensuring a stable stance.
• Engage the saw and allow the chain to reach full speed before making contact with the wood.
• Make smooth, controlled cuts. Avoid forcing the saw, as this can lead to kickback or damage.

Figure 4: The 8-inch bar and chain attachment in action, demonstrating its capability to cut through tree branches.

Figure 5: Overhead view of the pole saw being used to cut a branch, highlighting its maneuverability for various tasks.

3. Hedge Trimmer Operation

The 17.7-inch hedge trimmer is designed for shaping and trimming hedges and shrubs. It effortlessly cuts branches up to 0.6 inches in diameter.

• Hold the trimmer firmly with both hands.
• Use a sweeping motion to cut, moving the blade along the hedge.
• Avoid cutting branches larger than the specified diameter to prevent damage to the blades.
• The multi-angle head allows for precise trimming at various angles.

Figure 6: The 17.7-inch hedge trimmer attachment in use, demonstrating its ability to trim dense foliage.

4. String Trimmer Operation

The 10-inch string trimmer is ideal for trimming grass and edging lawns. It quickly converts from a trimmer to an edger.

• Hold the trimmer at a comfortable angle, keeping the cutting head parallel to the ground for trimming.
• For edging, rotate the head to a vertical position and guide it along the edge of sidewalks or flowerbeds.
• Maintain a safe distance from obstacles and ensure no one is in the immediate vicinity of the cutting line.

Figure 7: The 10-inch grass trimmer attachment being used for edging, showcasing its quick conversion capability.

Maintenance

Regular maintenance ensures the longevity and optimal performance of your Sun Joe GTS4002C system.

• Cleaning: After each use, remove the battery and clean the tool heads and main unit with a damp cloth. Remove any grass, sap, or debris from blades and cutting lines.
• Pole Saw Chain Maintenance: Regularly check the chain tension and lubricate the chain and bar with appropriate bar and chain oil. Sharpen the chain as needed or replace it when dull.
• Hedge Trimmer Blade Care: Keep the blades clean and free of sap and debris. Periodically apply a light machine oil to the blades to prevent rust and ensure smooth operation. If blades become dull, they may require sharpening by a professional.
• String Trimmer Line Replacement: Replace the trimmer line when it runs out or becomes too short. Refer to the specific instructions for your trimmer head for proper line winding.
• Battery Storage: Store the battery in a cool, dry place away from direct sunlight and extreme temperatures. For long-term storage, ensure the battery is partially charged (not fully charged or fully depleted).

Troubleshooting

If you encounter issues with your Sun Joe GTS4002C, refer to the following common troubleshooting steps:

If problems persist after attempting these solutions, please contact Sun Joe customer support.

Specifications

Warranty and Customer Support

Your Sun Joe GTS4002C lawn care system is backed by the Snow Joe + Sun Joe customer promise. New products are warranted for two years from the date of purchase. For further assistance, questions, or warranty claims, please contact Snow Joe + Sun Joe customer support at 1-866-766-9563.

Official Product Videos

No official product videos with relevant creator type (Seller) and accessible URLs were found in the provided product data to embed in this manual.