WAGNER Control Pro 350 M Airless Paint Sprayer Instruction Manual

1. Important Safety Information

Always prioritize safety when operating the WAGNER Control Pro 350 M Airless Paint Sprayer. Failure to follow these instructions may result in injury or property damage.

• Wear appropriate personal protective equipment (PPE) including a protective mask, gloves, and eye/face protection when using this product.
• Avoid direct contact with skin and eyes.
• Operate the sprayer in a well-ventilated area to prevent inhalation of fumes.
• Do not spray near open flames or sources of sparks.
• Keep the unit away from heat sources and direct sunlight.
• Store the sprayer in a cool, dry place, away from incompatible materials.
• Dispose of all contents and containers in accordance with local, state, and federal regulations.

2. Product Components

The WAGNER Control Pro 350 M includes the following components:

• Control Pro 350 M base unit
• High-quality Control Pro Airless spray gun
• 15-meter Airless hose
• HEA 311 and 517 reversible nozzles for thick or thin materials
• HEA Filter kit
• Instruction manual (this document)
• FFP2 protective mask

3. Setup Instructions

Follow these steps to prepare your WAGNER Control Pro 350 M for operation:

1. Unpack and Assemble: Carefully remove all components from the packaging. Assemble the base unit, attaching the wheels and telescopic handle if not already assembled.
2. Connect the Hose: Securely connect the 15-meter Airless hose to the sprayer unit and the spray gun. Ensure all connections are tight to prevent leaks.
3. Install Nozzle: Select the appropriate HEA nozzle (311 for thinner materials, 517 for thicker materials) and install it onto the spray gun.
4. Prepare Paint: Ensure your paint material is properly mixed and, if necessary, diluted according to the paint manufacturer's instructions and the sprayer's guidelines. The Control Pro 350 M is designed for direct suction from the paint container, allowing for quick and clean application.
5. Position the Suction Tube: Place the suction tube directly into the paint container.
6. Prime the System: Follow the priming procedure outlined in the detailed manual to remove air from the system and ensure a consistent paint flow.

For additional guidance on setup and optimal spray settings, consider downloading the WAGNER DIY App:

4. Operating Instructions

The WAGNER Control Pro 350 M is designed for professional Airless painting, offering up to 55% less overspray with maximum control. It is suitable for medium to large projects and frequent use.

1. Power On: Connect the sprayer to a suitable power source and turn it on.
2. Adjust Pressure: Set the desired pressure level. It is recommended to test the spray pattern on a piece of cardboard or scrap material before applying to your main surface.
3. Maintain Distance and Speed: Hold the spray gun at a consistent distance (typically 20-30 cm) from the surface and move it at a steady, even speed. Overlap each pass by approximately 50% for uniform coverage.
4. Telescopic Handle: Utilize the telescopic handle for easy transport and compact storage, especially useful when moving between different work areas.

5. Maintenance and Cleaning

Proper maintenance and cleaning are crucial for the longevity and optimal performance of your WAGNER Control Pro 350 M. Clean the unit immediately after each use.

1. Depressurize: Always depressurize the system before cleaning or performing any maintenance.
2. Flush with Water/Solvent: For water-based paints, flush the system thoroughly with clean water. For solvent-based paints, use the appropriate cleaning solvent recommended by the paint manufacturer. Run the cleaning agent through the pump, hose, and spray gun until it runs clear.
3. Clean Nozzle and Filter: Remove the nozzle and filter from the spray gun and clean them separately. The HEA nozzles are reversible for easy clearing of clogs.
4. Wipe Down Unit: Wipe down the exterior of the sprayer unit and hose with a damp cloth to remove any paint residue.
5. Storage: Store the cleaned and dried unit in a cool, dry place.

Note: Neglecting cleaning can lead to clogged nozzles and pump issues, significantly impacting performance.

6. Troubleshooting

This section addresses common issues you might encounter during operation. For more detailed troubleshooting, refer to the full product manual or the WAGNER DIY App.

• No Spray or Weak Spray:
  • Check if the unit is properly primed and there's no air in the system.
  • Ensure the suction tube is fully submerged in paint.
  • Inspect the nozzle for clogs. Use the reversible feature to clear it.
  • Check the filter for blockages.
  • Verify that the paint is adequately diluted for the sprayer.
• Inconsistent Spray Pattern:
  • Ensure consistent pressure settings.
  • Check for worn or damaged nozzles.
  • Verify paint consistency and proper mixing.
• Leaks:
  • Tighten all hose connections.
  • Inspect hoses and seals for damage.

7. Technical Specifications

8. Warranty and Support

WAGNER offers a standard three-year manufacturer's warranty for this product. You can extend this warranty by an additional year by registering your product online.

For any questions, issues, or technical support, please contact WAGNER customer service at: +39 0341 212 293.

You can also visit the official WAGNER store for more information and products: WAGNER Store.