Introduction
This manual provides essential instructions for the proper use, care, and maintenance of your Capresso 10-Cup Thermal Carafe, Model 4478.01. This thermal carafe is designed as a replacement for the Capresso CoffeeTEAM PRO Plus (Model # 488.05) and is not intended for universal use with other coffee makers. Its ergonomic design and stainless steel construction ensure your coffee remains hot for hours.
Figure 1: The Capresso 10-Cup Thermal Carafe, featuring its stainless steel body, black handle, and black lid with a pouring mechanism. This image illustrates the complete product.
Setup
Before first use, ensure the carafe is clean. This thermal carafe is specifically designed for the Capresso CoffeeTEAM PRO Plus (Model # 488.05). Verify compatibility with your coffee maker model before attempting to use.
- Unpack: Carefully remove the thermal carafe from its packaging. Inspect for any damage.
- Initial Cleaning: Wash the carafe and lid thoroughly with mild soap and warm water. Rinse completely. Refer to the "Maintenance" section for detailed cleaning instructions.
- Placement: Place the carafe securely on the warming plate or designated area of your compatible Capresso CoffeeTEAM PRO Plus coffee maker. Ensure the lid is properly seated.
Operating Instructions
The Capresso Thermal Carafe is designed to keep brewed coffee hot for extended periods without requiring a heating element, preserving flavor and preventing scorching.
Brewing Coffee
- Prepare Coffee Maker: Follow the instructions for your Capresso CoffeeTEAM PRO Plus (Model # 488.05) to prepare it for brewing.
- Place Carafe: Ensure the thermal carafe is correctly positioned under the coffee maker's brew basket. The lid should be in place to receive the brewed coffee.
- Start Brewing: Initiate the brewing cycle on your coffee maker. Coffee will drip directly into the thermal carafe.
Pouring Coffee
- The carafe features a drip-resistant spout and an ergonomic handle for comfortable and mess-free pouring.
- To pour, simply tilt the carafe. The lid is designed to allow pouring without removal, helping to maintain the coffee's temperature.
- For optimal heat retention, keep the lid securely closed when not pouring.
Maintenance and Cleaning
Proper cleaning and maintenance will extend the life of your thermal carafe and ensure optimal performance.
- Daily Cleaning: After each use, hand wash the carafe and lid with mild soap and warm water.
- Rinsing: Rinse thoroughly to remove all soap residue.
- Drying: Allow the carafe and lid to air dry completely before storing, or dry with a soft cloth.
- Vacuum Seal: To retain the vacuum seal and insulating properties, avoid harsh abrasives, scouring pads, or strong chemical cleaners. Do not immerse the entire carafe in water for extended periods.
- Stain Removal: For stubborn coffee stains inside the carafe, a mixture of baking soda and water, or a specialized coffee cleaner, can be used. Follow the cleaner's instructions and rinse thoroughly.
- Dishwasher Use: This thermal carafe is not dishwasher safe. Hand washing is required.
Troubleshooting
If you encounter issues with your Capresso Thermal Carafe, refer to the following common problems and solutions.
| Problem | Possible Cause | Solution |
|---|---|---|
| Coffee not staying hot | Lid not sealed properly; Vacuum seal compromised; Carafe not pre-heated (optional) | Ensure lid is securely closed. Check for damage to the carafe or lid. For best results, rinse the carafe with hot water before brewing. |
| Carafe leaks when pouring | Lid not positioned correctly; Damage to spout or lid mechanism | Verify the lid is properly aligned and seated. Inspect the spout and lid for cracks or damage. |
| Difficulty cleaning inside | Coffee residue buildup | Use a bottle brush for thorough cleaning. For stubborn stains, use a baking soda paste or specialized coffee cleaner. |
If the problem persists after attempting these solutions, please contact Capresso customer support.
Specifications
- Model Number: 4478.01
- Capacity: 10-cup (50-ounce)
- Material: Stainless Steel (carafe body), Plastic (handle and lid)
- Dimensions (L x W x H): Approximately 6.5 x 8.25 x 6.75 inches
- Item Weight: Approximately 1.86 pounds
- Compatibility: Specifically designed for Capresso CoffeeTEAM PRO Plus (Model # 488.05)
- Manufacturer: Capresso
Warranty and Support
For information regarding warranty coverage, product registration, or technical support, please refer to the documentation provided with your original Capresso CoffeeTEAM PRO Plus coffee maker or visit the official Capresso website.
You can typically find support contact information on the manufacturer's website:
When contacting support, please have your product model number (4478.01) and any relevant purchase information ready.
