1. Introduction
The GROHE Lineare Bathtub Spout, model 13383DC1, is a premium wall-mounted bath spout designed for modern bathrooms. Featuring a durable Supersteel finish and an elegant, minimalist design, this single-lever spout offers both aesthetic appeal and reliable functionality. This manual provides essential information for the safe installation, operation, and maintenance of your new GROHE product.
Image 1.1: GROHE Lineare Bathtub Spout, Supersteel finish. This image shows the sleek, modern design of the wall-mounted spout.
2. Safety Information
- Installation should be performed by a qualified professional to ensure proper function and compliance with local plumbing codes.
- Always turn off the main water supply before beginning any installation or maintenance work.
- Ensure all connections are secure and watertight to prevent leaks.
- Exercise caution when using hot water to avoid scalding. Test water temperature before use.
- Do not use abrasive tools or harsh chemicals for cleaning, as these can damage the product's finish.
3. Package Contents
Please verify that all components are present before beginning installation:
- GROHE Lineare Bathtub Spout (Model 13383DC1)
- Mounting hardware (screws, anchors, gaskets)
- Installation instructions (this document)
4. Setup and Installation
This bathtub spout is designed for wall-mounted, single-hole installation. Follow these steps carefully:
- Preparation: Turn off the main water supply to the bathroom. Clear the installation area and ensure the wall surface is clean and ready for mounting.
- Mounting Location: Determine the precise wall-mounting position for the spout. Mark the drilling points for the mounting plate.
- Secure Mounting Plate: Drill holes at the marked points and insert appropriate wall anchors. Attach the mounting plate securely to the wall using the provided screws. Ensure the plate is level.
- Connect Water Lines: Connect the hot and cold water supply lines to the corresponding inlets on the spout assembly. Use plumber's tape or thread sealant on all threaded connections to ensure a watertight seal.
- Install Spout: Carefully slide the bathtub spout onto the secured mounting plate, ensuring all connections are properly aligned and seated. Secure the spout to the mounting plate according to the specific hardware design.
- Test for Leaks: Slowly turn the main water supply back on. Carefully inspect all connections for any signs of leaks. Tighten connections as necessary.
- Final Check: Verify that the spout is firmly mounted and that water flows freely when operated.
Image 4.1: Side view of the GROHE Lineare Bathtub Spout. This image provides a different angle, useful for understanding the spout's profile during installation.
5. Operation
The GROHE Lineare Bathtub Spout features a single lever handle for intuitive control of both water flow and temperature.
- Water Flow: Lift the lever upwards to increase the water flow. Push the lever downwards to decrease the flow or to turn the water off completely.
- Temperature Control: Move the lever to the left for hot water and to the right for cold water. Adjust the lever's position between left and right to achieve your desired water temperature.
6. Maintenance and Care
To maintain the pristine Supersteel finish and ensure the longevity of your GROHE Lineare Bathtub Spout, follow these care instructions:
- Regular Cleaning: Clean the spout regularly with a soft cloth and a mild, non-abrasive soap or a cleaner specifically designed for bathroom fixtures.
- Avoid Harsh Cleaners: Do not use abrasive sponges, scouring pads, or cleaners containing harsh chemicals such as ammonia, bleach, or acids. These can damage the Supersteel finish and internal components.
- Rinse and Dry: After cleaning, thoroughly rinse the spout with clean water and dry it immediately with a soft, clean cloth to prevent water spots and mineral buildup.
7. Troubleshooting
If you encounter any issues with your bathtub spout, refer to the following common problems and solutions:
- Low Water Flow:
- Ensure the main water supply valves are fully open.
- Check the spout for any visible blockages or mineral buildup.
- Leaks from Connections:
- Turn off the water supply and carefully check all connections for tightness.
- Inspect gaskets and O-rings for damage and replace if necessary.
- If leaks persist, consult a professional plumber.
- Incorrect Water Temperature:
- Verify that the hot and cold water supply lines are correctly connected to the spout.
- Adjust the lever to the desired temperature range.
8. Specifications
| Brand | GROHE |
| Model Name | Lineare |
| Model Number | 13383DC1 |
| Material | Stainless Steel |
| Color | Supersteel |
| Mounting Type | Wall-mounted, Single-hole |
| Number of Handles | 1 |
| Handle Type | Lever |
| Valve Type | Cartridge Valve |
| Finish | Polished |
| Components Included | Linear Bathtub Spout |
| Country of Origin | China |
9. Warranty and Support
Manufacturer's Warranty: A 5-year manufacturer's warranty applies to this product when sold and shipped directly by Amazon. If the product is purchased from and shipped by a third-party seller, the warranty terms provided by that specific seller will apply.
Customer Support: For technical assistance, troubleshooting guidance, or to inquire about warranty claims, please contact GROHE customer service or the retailer from whom you purchased the product. Please have your model number (13383DC1) and proof of purchase available when contacting support.
