Introduction
The Nilight 5-pin rocker switch is a Single Pole Single Throw (SPST) on-off switch featuring illuminated LEDs. Its streamlined curved design and laser-etched patterns provide clear indication. The built-in LED light emits a soft glow, making it easy to locate the switch in dark environments. This switch is rated for 20A at 12V DC and 10A at 24V DC, commonly used with wiring harnesses to control various LED light fixtures in vehicles such as cars, Jeeps, 4X4s, SUVs, ATVs, UTVs, motorcycles, boats, and other off-road vehicles.
Features
- Easy to Install and Use: 5-pin on-off rocker switch with SPST design (single pole single Throw), simple installation, freely turn on or off the light.
- Cool Illuminated Light: Built-in two premium LEDs emit soft light to illuminate the patterns, easy for you to find the switch in the dark.
- Sturdy and Durable: Made of high-quality plastic and well-conductive pins; laser-etched pattern, not easy to fade away.
- Wide Application: Available for controlling LED light bar, LED work lights, fog lamps, driving lights, headlights, taillights, off road lights, etc.
Package Contents
- 1 x 5-Pin Rocker Switch
- 1 x Jumper Wires Set
- 1 x Wiring Diagram
Image: The Nilight 5-Pin Rocker Switch shown with its included jumper wires.
Installation and Wiring
The Nilight rocker switch is designed for easy installation. It fits into common square holder panel housings found in most vehicles. The following sections detail two common wiring methods.
Wiring Method A: Accessory Switched Power Source
In this method, the lower light of the switch will turn on only when the vehicle's key is turned to the ON position. This is suitable for accessories that should only be active when the vehicle is running or in accessory mode.
Image: Detailed wiring diagram for Method A, showing connections to ground, battery, and outgoing relay.
Pin-Tab Outs:
- Pin 8: Upper Light Negative (-) source
- Pin 7: Lower Light Negative (-)
- Pin 2: Incoming from power
- Pin 3: Outgoing to relay, accessory or equipment
- Pin 6: Lower Light Positive (+)
Refer to the included wiring diagram for precise pin connections. Ensure all connections are secure and insulated to prevent short circuits.
Wiring Method B: Constant Power Source/Battery
With this method, the lower light of the switch will turn on only when the switch itself is turned to the ON position. This is ideal for accessories that need to be powered independently of the vehicle's ignition state.
The pin-tab outs for Method B are the same as Method A, but the power source connection for Pin 2 will be a constant battery source rather than an accessory switched source.
Jumper Wires and Connections:
The included jumper wires facilitate easy connection to the switch terminals. Press down on the clips of the wire terminals to connect or disconnect them easily.
Image: Illustration of how to easily connect and disconnect the jumper wires from the switch terminals.
Image: Demonstrates how the rocker switch fits into a compatible housing (housing sold separately).
For a visual guide on wiring and installation, please refer to the official product video below:
Video: Official Nilight video demonstrating the installation and functionality of the 5-pin SPST rocker switches, including wiring methods and light operation.
Operating Instructions
The Nilight rocker switch operates as a simple ON/OFF mechanism. Once properly wired and installed, press the top part of the switch to turn the connected accessory ON, and press the bottom part to turn it OFF. The illuminated LED light on the switch will indicate its current state (ON/OFF), making it easy to see in various lighting conditions.
Image: Shows the LED lighting effect of the switch, with words and pattern illuminating when powered on.
Image: Close-up of the illuminated switch, highlighting the two premium LEDs and laser-etched pattern.
Image: An example of multiple Nilight rocker switches installed in a vehicle's dashboard, demonstrating their illuminated appearance during use.
The laser-etched pattern is designed to be durable and not easily fade, ensuring long-lasting visibility.
Maintenance
To ensure the longevity and proper functioning of your Nilight rocker switch, follow these general maintenance guidelines:
- Cleaning: Use a soft, dry cloth to wipe the surface of the switch. Avoid abrasive cleaners or solvents that could damage the plastic or laser-etched pattern.
- Connection Check: Periodically inspect the wiring connections to ensure they remain secure and free from corrosion. Loose connections can lead to intermittent operation or electrical issues.
- Environmental Protection: While the switch is designed for automotive environments, avoid prolonged exposure to extreme moisture or direct submersion, as this can affect its internal components.
- Avoid Overloading: Ensure the connected load does not exceed the switch's rated current (20A/12V DC, 10A/24V DC) to prevent damage to the switch or wiring.
Troubleshooting
If you encounter issues with your Nilight rocker switch, consider the following troubleshooting steps:
- Switch Not Lighting Up:
- Check power supply to the switch. Ensure the vehicle's ignition is on if using an accessory switched power source (Method A).
- Verify all wiring connections are correct and secure, especially the ground and power input pins.
- Inspect the LED lights for any visible damage.
- Connected Device Not Turning On/Off:
- Confirm the switch is receiving power.
- Check the wiring from the switch's outgoing pin (Pin 3) to the connected device or relay.
- Ensure the connected device itself is functioning correctly and its power requirements are met.
- Verify that the current draw of the connected device does not exceed the switch's maximum rating.
- Intermittent Operation:
- Check for loose or corroded connections at the switch terminals or elsewhere in the circuit.
- Ensure the switch is firmly seated in its housing.
If problems persist after following these steps, please contact Nilight customer service for further assistance.
Specifications
| Specification | Value |
|---|---|
| Brand | Nilight |
| Item Model Number | 90001R |
| Product Dimensions | 1 x 0.5 x 1 inches; 0.32 ounces |
| Operation Mode | ON-OFF |
| Current Rating | 20 Amps (12V DC), 10 Amps (24V DC) |
| Operating Voltage | 12V / 24V DC |
| Contact Type | Normally Closed |
| Connector Type | Plug In |
| Terminal | Pin |
| Circuit Type | SPST |
| Actuator Type | Rocker |
Image: A comparison table highlighting key specifications of the Nilight 5-pin rocker switch against other similar products.
Image: Visual representation of the rocker switch dimensions and details about its sturdy and durable construction.
Warranty and Support
Nilight provides a 2-year warranty for this product. For any questions, technical assistance, or warranty claims, please feel free to contact Nilight professional customer service. Refer to the product packaging or the official Nilight website for the most current contact information.
