Introduction
Welcome to the TYLT Smart Charger 3X. This portable charging solution combines a wall charger with a built-in 6700 mAh battery, offering convenient power for your Micro-USB devices. This manual provides instructions for the safe and efficient use of your Smart Charger 3X.
Safety Information
Please read all safety warnings before using this product to ensure proper operation and to prevent damage to the device or injury.
- Do not expose the device to water, moisture, or extreme temperatures.
- Keep out of reach of children.
- Do not disassemble, modify, or attempt to repair the device. This will void the warranty.
- Avoid dropping or subjecting the device to severe impacts.
- Dispose of the product responsibly according to local regulations for electronic waste.
- Use only with compatible devices and cables.
Package Contents
Verify that all items are present in your package:
- TYLT Smart Charger 3X
- User Guide (this document)
- Warranty Insert
Product Overview
Familiarize yourself with the components of your TYLT Smart Charger 3X.
Setup
Before initial use, it is recommended to fully charge your TYLT Smart Charger 3X.
- Unfold Wall Prongs: Gently pull out the foldable wall prongs located on the side of the charger.
- Plug into Wall Outlet: Insert the charger directly into a standard AC wall outlet.
- Initial Charge: The LED indicators will illuminate to show the charging status of the internal battery. Allow the unit to charge until all LEDs are solid, indicating a full charge.
Operating Instructions
Charging the Smart Charger 3X
The Smart Charger 3X can be recharged via its built-in wall prongs.
- Extend the wall prongs and plug the unit into an AC wall outlet.
- The LED indicators will show the charging progress. All four LEDs will be solid when fully charged.
Charging Your Devices
The Smart Charger 3X can charge up to two devices simultaneously.
- Using the Built-in Micro-USB Cable: Extend the integrated Micro-USB cable and connect it directly to your Micro-USB compatible device.
- Using the USB-A Output Port: Connect your device's charging cable (e.g., USB-A to Lightning, USB-A to USB-C) to the USB-A output port on the side of the Smart Charger 3X, then connect the other end to your device.
- Press the power button once to initiate charging if the device does not begin charging automatically.
- The LED indicators will show the remaining battery level of the Smart Charger 3X.
Intelligent Power Routing
When the Smart Charger 3X is plugged into a wall outlet and also charging a device, it prioritizes power delivery. Your connected device will receive power first, ensuring it charges efficiently. Once your device is fully charged, the Smart Charger 3X will then begin recharging its internal battery.
LED Indicator Guide
The LED lights on the Smart Charger 3X provide information about its battery status:
| Number of Solid LEDs | Battery Level |
|---|---|
| 1 LED | 0-25% |
| 2 LEDs | 25-50% |
| 3 LEDs | 50-75% |
| 4 LEDs | 75-100% (Full) |
During charging, the active LED will blink, and subsequent LEDs will become solid as the charge level increases.
Maintenance
Proper care will extend the life of your Smart Charger 3X.
- Cleaning: Use a soft, dry cloth to clean the exterior of the charger. Do not use liquid cleaners or aerosols.
- Storage: Store the charger in a cool, dry place away from direct sunlight and extreme temperatures.
- Battery Care: For optimal battery health, fully charge the unit at least once every three months if not in regular use.
Troubleshooting
If you encounter issues with your Smart Charger 3X, refer to the following common solutions:
- Charger not charging: Ensure the wall prongs are fully extended and securely plugged into a live AC outlet. Check if the outlet is functioning.
- Device not charging: Ensure the Smart Charger 3X has sufficient battery charge (check LEDs). Verify that the charging cable (built-in or external) is securely connected to both the charger and your device. Press the power button on the Smart Charger 3X.
- Slow charging: Ensure you are using a compatible cable. Some devices may charge slower if multiple devices are connected or if the Smart Charger 3X itself is also being recharged.
- LEDs not lighting up: The battery may be completely depleted. Plug the charger into a wall outlet for an extended period. If still unresponsive, contact customer support.
Specifications
| Feature | Detail |
|---|---|
| Model Number | MICSC3XSST |
| Battery Capacity | 6700 mAh (Lithium Ion) |
| Product Dimensions | 7 x 2 x 4 inches |
| Item Weight | 6.4 ounces |
| Connectivity | Built-in Micro-USB cable, 1x USB-A Output Port |
| Special Features | Fast Charging, Travel-friendly design with built-in wall prongs |
| Compatible Devices | Universal/Smartphones compatible with Micro-USB or USB-A charging cables |
| Color | Gold |
| Manufacturer | Tylt |
Warranty Information
The TYLT Smart Charger 3X comes with a limited manufacturer's warranty. Please refer to the separate Warranty Insert included in your package for detailed terms, conditions, and registration information. Keep your proof of purchase for warranty claims.
Customer Support
For further assistance, technical support, or warranty inquiries, please visit the official TYLT website or contact their customer service department. Contact details can typically be found on the manufacturer's website or the warranty insert.
TYLT Official Website: www.tylt.com (Please note: This is a placeholder URL as the exact support link was not provided in the product data.)