Introduction
This manual provides essential instructions for the proper use, maintenance, and troubleshooting of the Permatex FORM-A-SEAL Leak Repair product, model 82096. This aerosol product is specifically designed to quickly and effectively stop various types of engine leaks. Please read this manual thoroughly before use to ensure optimal performance and safety.
Product Overview
An image of the Permatex FORM-A-SEAL Leak Repair product. It is an aerosol can, primarily blue with white text, featuring the Permatex logo and the product name 'FORM-A-SEAL LEAK REPAIR'. The can also displays 'ITEM NO. 82096' and indicates 'NET WT. 5 OZ./CONT. NET. 142g'. A graphic depicting a leaking hose is visible on the label. Cautionary text regarding contents under pressure is also present.
Permatex FORM-A-SEAL Leak Repair is an easy-to-use aerosol solution for common engine leaks. Its unique formula creates a durable, waterproof seal, helping to extend the life of engine components and prevent fluid loss.
Setup
Preparation
- Ensure the engine is completely cool and turned off before attempting any repair. This prevents burns and ensures proper product adhesion.
- Thoroughly clean the area around the leak. Remove any oil, grease, dirt, or debris using a suitable degreaser and a clean cloth. The surface must be dry and free of contaminants for the product to adhere effectively.
- Shake the Permatex FORM-A-SEAL can vigorously for at least one minute to ensure the contents are well mixed. Continue to shake periodically during application.
Operating Instructions
Application
- Hold the can upright, approximately 6 to 8 inches (15-20 cm) away from the leak area.
- Spray a thin, even coat directly onto the leak. Ensure complete coverage of the affected area.
- Allow the first coat to dry for 10 to 15 minutes. The drying time may vary depending on temperature and humidity.
- Apply additional thin coats as needed, allowing adequate drying time between each coat. For optimal results, two to three coats are typically recommended.
- For maximum strength and durability, allow the repaired area to cure for a full 24 hours before operating the engine or exposing it to fluids.
Maintenance
Storage and Care
- Store the Permatex FORM-A-SEAL can in a cool, dry place, away from direct sunlight, heat sources, and open flames.
- Ensure the cap is securely replaced on the can after each use to prevent drying out and maintain product integrity.
- Keep out of reach of children and pets.
Troubleshooting
Common Issues and Solutions
| Problem | Solution |
|---|---|
| Leak persists after application. | Ensure the surface was thoroughly cleaned and dry before application. Apply additional coats, allowing sufficient drying time between each application. For larger or high-pressure leaks, multiple applications or professional mechanical repair may be required. |
| Product does not spray or sprays unevenly. | Ensure the nozzle is not clogged. If clogged, remove and clean the nozzle with a thin wire or pin. Shake the can vigorously for at least one minute before and during use to ensure proper mixing and flow. Ensure the can is not too cold; allow it to warm to room temperature if necessary. |
Specifications
Technical Data
| Attribute | Detail |
|---|---|
| Brand | Permatex |
| Model Number | 82096 |
| Item Form | Aerosol |
| Package Information | Aerosol Can |
| Net Weight | 5 oz (142g) |
| Water Resistance Level | Waterproof |
| UPC | 079340820968 |
| Product Dimensions | Approximately 10 x 10 x 10 inches |
| Item Weight | 6.4 ounces |
Warranty Information
Permatex products are manufactured to high-quality standards. For specific warranty details regarding your Permatex FORM-A-SEAL Leak Repair, please refer to the product packaging or visit the official Permatex website. Keep your purchase receipt as proof of purchase.
Support
If you have any questions or require further assistance with your Permatex FORM-A-SEAL Leak Repair, please contact Permatex customer support. You can typically find contact information, including phone numbers and email addresses, on the Permatex official website or on the product packaging. Please have the product model number (82096) and UPC (079340820968) ready when contacting support.
