1. Introduction
This manual provides instructions for the USARMT replacement remote control, designed for use with Avera TV models 40AER10, 32AER10, and 55AER10. This remote is pre-programmed and requires no setup or programming. Simply insert batteries to begin operation.
2. Setup
2.1 Battery Installation
The remote control requires two AAA batteries (not included). Follow these steps to install them:
- Locate the battery compartment cover on the back of the remote control.
- Press down on the tab and slide the cover off.
- Insert two AAA batteries, ensuring the positive (+) and negative (-) terminals align correctly with the markings inside the compartment.
- Slide the battery compartment cover back into place until it clicks securely.
Note: This remote is pre-programmed and ready to use once batteries are installed. No additional setup is required.
Figure 1: USARMT Replacement Avera TV Remote Control. The battery compartment is located on the back of the device.
3. Operating Instructions
This section describes the functions of the buttons on your USARMT replacement remote control.
| Button | Function |
|---|---|
| POWER (Red Button) | Turns the TV on or off. |
| DISPLAY | Displays current channel information or other on-screen data. |
| GUIDE | Accesses the electronic program guide (EPG). |
| FAV | Accesses favorite channels list. |
| FREEZE | Pauses the current picture on screen. |
| PICTURE | Adjusts picture settings (e.g., brightness, contrast). |
| TEMP | May adjust color temperature or other display settings. |
| EXIT | Exits current menu or on-screen display. |
| RETURN | Returns to the previous menu or channel. |
| Navigation Arrows (Up, Down, Left, Right) | Navigates through menus and options. |
| ENTER | Confirms selections in menus. |
| SLEEP | Sets the TV to turn off automatically after a set period. |
| MENU | Opens the main TV menu. |
| ASPECT | Changes the screen aspect ratio (e.g., 16:9, 4:3). |
| VOL +/- (Blue Button) | Increases or decreases the volume level. |
| MUTE | Mutes or unmutes the TV audio. |
| CH +/- (Green Button) | Changes the TV channel up or down. |
| LAST | Switches to the previously viewed channel. |
| 0-9 (Number Pad) | Directly enters channel numbers. |
| INPUT | Selects the video input source (e.g., HDMI, AV). |
| AUDIO | Selects audio options or tracks. |
| MTS | Selects Multi-channel Television Sound options (e.g., Stereo, SAP). |
| CCD | Activates or deactivates Closed Captioning. |
| Play/Pause, Stop, Rewind, Fast Forward | Controls media playback functions (if supported by the TV). |
| REP | Repeat function for media playback. |
| CH.LIST | Displays the channel list. |
4. Maintenance
4.1 Battery Replacement
Replace batteries when the remote's response becomes sluggish or stops working. Always replace both batteries at the same time with new AAA batteries. Do not mix old and new batteries, or different types of batteries.
4.2 Cleaning
To clean the remote control, wipe it with a soft, dry cloth. Do not use liquid cleaners or abrasive materials, as these can damage the remote's surface or internal components.
4.3 Storage
Store the remote control in a cool, dry place away from direct sunlight and extreme temperatures. If the remote will not be used for an extended period, remove the batteries to prevent leakage.
5. Troubleshooting
If you experience issues with your remote control, refer to the following common problems and solutions:
- Remote is not responding:
- Ensure batteries are installed correctly with the correct polarity.
- Replace old batteries with new AAA batteries.
- Check for any obstructions between the remote and the TV's infrared sensor. Ensure a clear line of sight.
- Confirm that the remote is pointed directly at the TV.
- Remote only works when very close to the TV:
- This can indicate low battery power. Replace the batteries.
- Ensure there are no strong light sources (like direct sunlight or bright fluorescent lights) interfering with the TV's IR receiver.
- Certain buttons do not work:
- Check for dirt or debris lodged under the button. Gently clean the remote.
- If only specific buttons fail, the remote may be damaged.
- Remote does not control the TV model:
- Verify that your Avera TV model is one of the compatible models: 40AER10, 32AER10, or 55AER10. This remote is specifically designed for these models and may not function with others.
6. Specifications
| Feature | Detail |
|---|---|
| Brand | USARMT |
| Compatible TV Models | Avera 40AER10, 32AER10, 55AER10 |
| Connectivity Technology | Infrared (IR) |
| Power Source | 2 x AAA Batteries (not included) |
| Pre-programmed | Yes, no setup required |
| Item Weight | Approximately 1 pound (including packaging) |
| Special Feature | Ergonomic design |
7. Warranty and Support
This USARMT replacement remote control comes with a 30-day hassle-free return policy. If you encounter any issues or are not satisfied with the product within 30 days of purchase, please refer to your retailer's return process for a refund or replacement.
For further assistance, please contact the seller through the platform where the purchase was made.