BURCAM 506227P Shallow Well Jet Pump System

1. Introduction

This manual provides essential information for the safe and efficient installation, operation, and maintenance of your BURCAM 506227P 3/4 HP Noryl Shallow Well Jet Pump System. This system is designed for shallow wells up to 25 feet deep, offering a pumping capacity of up to 850 gallons per hour. Its Noryl pump body ensures corrosion resistance and quieter operation, providing cleaner, rust-free water.

Please read this manual thoroughly before attempting to install or operate the pump system. Keep it for future reference.

Figure 1: BURCAM 506227P Shallow Well Jet Pump System. This image shows the complete pump unit with its integrated pressure tank and motor.

2. Safety Information

Always observe basic safety precautions to reduce the risk of fire, electric shock, and personal injury. This pump system operates with electricity and water, which can be hazardous if not handled correctly.

• Electrical Safety: Ensure the pump is properly grounded. Disconnect power before servicing. Do not operate with damaged cords or plugs.
• Water Pressure: The system operates under pressure. Relieve pressure before opening any part of the system.
• Installation: Installation should be performed by qualified personnel in accordance with local electrical and plumbing codes.
• Operating Environment: Do not use in explosive atmospheres or to pump flammable liquids. Protect the pump from freezing temperatures.
• Children: Keep children away from the pump system during operation.

3. Package Contents

Upon unpacking, verify that all components are present and undamaged:

• BURCAM 506227P Shallow Well Jet Pump
• Integrated Pressure Tank
• Pressure Gauge
• Instruction Manual

Note: A foot valve/check valve is required for use with shallow wells and is sold separately.

4. Setup and Installation

Proper installation is crucial for the pump's performance and longevity. This pump is designed for shallow wells up to 25 feet deep.

4.1 Location

• Install the pump as close to the well as possible.
• Ensure the location is dry, well-ventilated, and protected from freezing temperatures and direct sunlight.
• Mount the pump on a firm, level surface to minimize vibration.

4.2 Plumbing Connections

• The pump features a 1-1/4 inch suction inlet and a 1 inch discharge outlet.
• Connect the suction line from the well to the pump's inlet. Ensure all connections are airtight to prevent air leaks, which can cause the pump to lose prime.
• Install a foot valve or check valve at the end of the suction line in the well to maintain prime.
• Connect the discharge line to your household or irrigation system.
• Use appropriate thread sealant on all pipe connections.

Figure 2: Side view of the BURCAM 506227P pump, illustrating the suction and discharge connections.

4.3 Electrical Connections

• The pump is equipped with an industrial-type motor, operating at 115/230 Volts. Verify your power supply matches the pump's requirements.
• Ensure the electrical circuit is protected by a fuse or circuit breaker of the correct rating.
• All wiring must comply with local electrical codes and be performed by a qualified electrician.
• The motor is fan-cooled and includes a factory-preset 30/50 pressure switch.

5. Operating Instructions

5.1 Priming the Pump

1. Before initial startup, the pump casing must be filled with water. Locate the priming plug on the top of the pump.
2. Remove the priming plug and slowly fill the pump casing with clean water until it overflows.
3. Replace the priming plug securely.
4. Open a faucet in the discharge line to allow air to escape.

5.2 Starting the Pump

1. Ensure all connections are tight and the pump is primed.
2. Turn on the power supply to the pump. The pump should start running.
3. Monitor the pressure gauge. Once the system reaches the cut-off pressure (typically 50 PSI), the pump will shut off.
4. Close the open faucet. The pump will cycle on and off as water is used and pressure drops.

The pump has a maximum discharge flow of 850 gallons per hour and is designed for a maximum pumping height of 150 feet.

6. Maintenance

Regular maintenance ensures optimal performance and extends the life of your pump system.

• Pressure Tank: The integrated pressure tank bladder is designed to prevent water-to-metal contact and condensation, reducing corrosion. Periodically check the air pre-charge in the tank (when the pump is off and system pressure is relieved) to ensure it matches the manufacturer's recommendation (typically 2 PSI below the pump's cut-in pressure).
• Cleanliness: Keep the pump and motor clean and free of debris to ensure proper cooling.
• Leak Checks: Regularly inspect all plumbing connections for leaks. Tighten as necessary.
• Winterization: In areas subject to freezing temperatures, the pump and all exposed piping must be completely drained or protected from freezing. Disconnect power, open drain plugs, and remove priming plugs to ensure all water is removed.

7. Troubleshooting

This section provides solutions to common issues you might encounter.

8. Specifications

9. Warranty Information

The BURCAM 506227P Shallow Well Jet Pump System is covered by a 2-year limited warranty from the date of purchase. This warranty covers defects in materials and workmanship under normal use and service.

For full warranty terms and conditions, please refer to the official BurCam website or contact customer support. Keep your proof of purchase for warranty claims.

10. Support and Contact

If you require further assistance, have questions, or need to report an issue, please contact BurCam customer support.

• Website: Visit the official BurCam website for FAQs, product registration, and additional resources.
• Contact: Refer to the BurCam website for current contact information, including phone numbers and email addresses for technical support.

When contacting support, please have your pump model number (506227P) and date of purchase readily available.