1. Important Safety Information
Read all instructions before installing or using this heater. Failure to follow these instructions may result in fire, electric shock, serious injury, or death.
- Electrical Protection: Protect the unit with appropriate circuit breakers or fuses as per the nameplate specifications.
- Voltage Compatibility: Ensure the supply voltage (volts) matches the rating indicated on the heater's nameplate.
- Grounding: This unit must be properly grounded.
- Wiring: Use copper conductors only. Power leads must be suitable for 75°C (167°F).
- Power Disconnection: Always switch off the power supply to the unit at the circuit breaker/fuse before any installation, repair, or cleaning.
- Intended Use: Verify that the heater is suitable for its intended application. Consult the product catalog or a representative if unsure.
- Recommended Heating Capacity: For optimal performance, a heating capacity of 1.25 W per cubic foot (0.03 m³) is recommended.
2. Product Overview
The Uniwatt by Stelpro UHC1002W is a modern, surface-mounted convector heater designed for quiet and efficient heating. It features a durable 22-gauge steel cabinet and an integrated electronic thermostat for precise temperature control.
Front view of the Uniwatt by Stelpro UHC1002W Convector Heater.
Side view illustrating the slim profile of the convector heater.
Detail of the effective heating elements: two stainless steel tubular sheathed elements isolated with nylon sleeves to reduce expansion and contraction noises.
The heater's design promotes efficient airflow, drawing cool air from below and expelling warm air through the front grille, creating a chimney effect for consistent heat distribution.
3. Installation Instructions
This heater is designed for surface or wall-mounted installation. Ensure power is disconnected at the circuit breaker before beginning installation.
3.1 Mounting
- The heater must be mounted with a minimum clearance of 4 inches (10 cm) from the floor.
- Utilize the concealed mounting bracket for a secure and tidy installation.
Image illustrating the concealed mounting bracket for wall installation.
3.2 Electrical Connection
- The heater requires a 240V hardwired connection.
- Use the back entry plate with cable clamps for a secure and organized wiring setup within the junction box.
- All wiring must comply with local electrical codes and regulations.
Diagram showing a typical 240V hardwired connection within a junction box.
4. Operating Instructions
The Uniwatt UHC1002W heater features a built-in electronic thermostat for precise temperature control and energy optimization.
4.1 Setting the Temperature
- Use the control buttons adjacent to the digital display to adjust the desired room temperature.
- The electronic thermostat will maintain the set temperature, cycling the heater on and off as needed.
Close-up view of the integrated electronic thermostat display and control buttons.
5. Maintenance
Regular maintenance ensures optimal performance and longevity of your heater. Always disconnect power at the circuit breaker before performing any maintenance.
5.1 Cleaning
- Clean the exterior of the heater with a soft, damp cloth. Do not use abrasive cleaners or solvents.
- Ensure the air intake and exhaust grilles are free from dust and debris to maintain proper airflow.
6. Troubleshooting
If you experience issues with your Uniwatt convector heater, consult the following table for common problems and solutions.
| Problem | Possible Cause | Solution |
|---|---|---|
| Heater does not turn on | No power supply; Circuit breaker tripped; Thermostat set too low | Check circuit breaker; Ensure power is on; Increase thermostat setting |
| Insufficient heating | Thermostat set too low; Obstruction of air grilles; Heater size inadequate for room | Increase thermostat setting; Clear grilles; Refer to heating capacity guidelines |
| Unusual noises | Dust or debris inside unit; Loose mounting | Disconnect power and inspect/clean; Ensure heater is securely mounted |
If the problem persists after attempting these solutions, contact customer support.
7. Specifications
| Feature | Detail |
|---|---|
| Brand | Stelpro (Uniwatt) |
| Model Number | UHC1002W |
| Power/Wattage | 1000 Watts |
| Voltage | 240 Volts |
| Material | 22-gauge Steel |
| Colour | White |
| Product Dimensions | 58.1 x 10 x 44.61 cm (22 7/8" W x 3 7/32" D x 17 9/16" H) |
| Item Weight | 6.03 kg |
| Special Features | Built-in Electronic Thermostat |
| Mounting Type | Wall Mount (Surface) |
| Indoor/Outdoor Usage | Indoor |
| Heating Method | Convection |
Dimensional diagram of the Uniwatt convector heater.
Indication that the product is proudly made in Canada.
8. Warranty and Support
8.1 Warranty
This Uniwatt by Stelpro convector heater comes with a 2-year warranty from the date of purchase, covering defects in material and workmanship under normal use.
8.2 Customer Support
For technical assistance, warranty claims, or any questions regarding your heater, please contact Stelpro customer service:
- Phone: 1-844-783-5776
- Email: info@stelpro.com
- Address: 1041 Rue Parent, Saint-Bruno-de-Montarville, QC J3V 6L7
