Introduction
The Aokeo AK-35 Microphone Suspension Boom Scissor Arm Stand is engineered for stability and flexibility, providing an optimal microphone positioning solution for various audio recording and broadcasting needs. Constructed from high-quality steel with an electrostatic powder coating, this stand offers enhanced durability and rust resistance. Its design incorporates super spring support, allowing for smooth and solid movement without dipping or sinking, ensuring your microphone remains precisely where you need it.
Package Contents
- Aokeo AK-35 Microphone Suspension Boom Scissor Arm Stand
- Desktop Mounting Clamp
- Microphone Clip (for standard microphones)
- 3/8" to 5/8" Adapter (for wider compatibility)
- Warranty Card
Setup Instructions
Follow these steps to properly set up your Aokeo AK-35 Microphone Arm Stand:
1. Attach the Desktop Mounting Clamp
Secure the desktop mounting clamp to a sturdy surface, such as a desk or table edge. Ensure the clamp is tightened firmly to prevent movement. The clamp can accommodate surfaces up to 2.3 inches (6 cm) thick.
Figure 1: Attaching the desktop clamp.
2. Insert the Microphone Arm into the Clamp
Slide the base of the microphone arm into the hole on the desktop clamp. Tighten the knob on the clamp to secure the arm. The arm's base allows for 360° rotation.
Figure 2: Inserting the microphone arm into the clamp.
3. Attach Your Microphone
The arm comes with a standard microphone clip. If your microphone (e.g., Blue Snowball, Blue Yeti) requires a different adapter, detach the included clip and use the provided 3/8" to 5/8" adapter or your microphone's specific adapter. Screw your microphone or shock mount onto the threaded screw adapter at the end of the arm.
Note:
- For Elgato Wave microphones, first install the Elgato Wave onto its shock mount, then attach the shock mount to the mic arm.
- The arm supports a maximum load of approximately 70 oz (1.8 KG).
Figure 3: Microphone compatibility and attachment.
Setup Video Guide:
Video 1: Official Aokeo AK-35 Multi-Function Microphone Arm Stand setup and usage guide.
Operating Instructions
The Aokeo AK-35 arm stand offers multi-angle adjustment for optimal microphone placement.
Adjusting the Arm Position
The arm features multiple joints that can be adjusted to position your microphone precisely. The main arm sections can bend up to 180 degrees, and the microphone attachment point can rotate up to 270 degrees. The base also allows for a full 360-degree rotation.
Figure 4: Flexible adjustment points of the arm stand.
Figure 5: Detailed view of adjustment mechanisms.
Cable Management
Utilize the included velcro ties to secure your microphone cable along the arm, keeping your workspace tidy and preventing cable interference.
Maintenance
- Cleaning: Wipe the stand with a soft, dry cloth to remove dust. Avoid abrasive cleaners or solvents.
- Joint Lubrication: Periodically check the joints for smooth movement. If stiffness occurs, a small amount of silicone-based lubricant can be applied to the pivot points.
- Tightness Check: Regularly inspect all screws and knobs to ensure they are securely tightened. This maintains stability and prevents accidental drops.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Microphone arm sags or does not hold position. | Joints are not tightened sufficiently; microphone is too heavy. | Ensure all adjustment knobs are securely tightened. Verify your microphone's weight does not exceed the 1.8 KG (70 oz) maximum load capacity. |
| Microphone does not fit the arm's screw adapter. | Incorrect thread size. | Use the included 3/8" to 5/8" adapter or your microphone's specific adapter. |
| Arm feels stiff or difficult to adjust. | Lack of lubrication or overtightened joints. | Loosen adjustment knobs slightly. Apply a small amount of silicone-based lubricant to the pivot points if necessary. |
| Springs are noisy during adjustment. | Normal operation, but can be reduced. | Consider sleeving the springs with heat shrink wrap or electrical tape to reduce mechanical noise. |
Specifications
| Feature | Detail |
|---|---|
| Model Number | AK-35 |
| Material | High-Quality Steel |
| Finish | Electrostatic Powder Spraying |
| Max Load Capacity | Approx. 70 oz (1.8 KG) |
| Desktop Clamp Thickness | Up to 2.3 inches (6 cm) |
| Arm Length (each section) | 350mm (13.8 inches) |
| Connector Type | 3/8" thread (with 5/8" adapter included) |
| Item Weight | 1.54 pounds (0.7 KG) |
| Product Dimensions | 16 x 4 x 2 inches |
Warranty and Support
Aokeo products are designed for reliability and performance. For specific warranty information, please refer to the warranty card included in your package. For technical support, product inquiries, or assistance with any issues, please contact Aokeo customer service through their official channels or the retailer where the product was purchased.
