Introduction
This manual provides instructions for the BENINCA TO.GO 2WV remote control transmitter. This device is designed for controlling compatible BENINCA gate or garage door openers. Please read this manual thoroughly before use to ensure proper operation and safety.
Safety Information
- Keep the remote control out of reach of children to prevent accidental operation.
- Do not expose the device to water, excessive moisture, or extreme temperatures.
- Dispose of used batteries properly according to local regulations.
- Always ensure the area around the gate or garage door is clear of people, pets, and obstructions before operating the system.
Product Overview
The BENINCA TO.GO 2WV is a compact 433.92Mhz rolling code keyfob equipped with two buttons, allowing control over two distinct functions of your BENINCA automated system. Its design prioritizes ease of use and portability.
Image: The BENINCA TO.GO 2WV remote control, featuring a black casing and two prominent white control buttons. The 'TO.GO' branding is visible below the buttons.
Setup and Programming
The BENINCA TO.GO 2WV remote control utilizes a rolling code system and must be programmed directly to your BENINCA receiver unit or control board. The specific programming procedure varies depending on your BENINCA gate or garage door opener model.
General Programming Steps (Consult your receiver's manual for exact instructions):
- Access the Receiver: Locate the programming button or menu on your BENINCA gate/garage door opener's control board. This may require opening the control unit casing.
- Activate Programming Mode: Press and hold the programming button on the receiver until an indicator light (LED) changes state (e.g., starts flashing).
- Transmit Code: While the receiver is in programming mode, press and hold the desired button on your new BENINCA TO.GO 2WV remote control for a few seconds.
- Confirm Programming: The receiver's indicator light should change again (e.g., turn solid or flash rapidly) to confirm successful programming.
- Test Operation: Once programmed, test the remote control to ensure it operates the gate or garage door correctly.
- Program Additional Remotes: Repeat the process for any additional remote controls.
Important: Always refer to the specific instruction manual for your BENINCA gate or garage door opener's receiver for detailed and accurate programming steps.
Operation
To operate your BENINCA TO.GO 2WV remote control, simply press the programmed button corresponding to the desired function (e.g., open/close gate, open/close garage door). Ensure you are within the operational range of the receiver for reliable communication.
Maintenance
Battery Replacement:
The remote control is powered by a standard coin cell battery. When the remote's operational range decreases or the indicator light (if present) fails to illuminate upon button press, the battery may need replacement.
- Carefully open the remote control casing, typically by prying it apart at a seam using a small flat-head screwdriver.
- Note the orientation of the existing battery before removal.
- Remove the old battery and insert a new one of the same type (e.g., CR2032), ensuring correct polarity (+ side up).
- Close the remote control casing securely until it clicks into place.
Cleaning:
Wipe the remote control with a soft, dry cloth to remove dust or smudges. Do not use abrasive cleaners, solvents, or immerse the device in liquids, as this can damage the electronics.
Troubleshooting
- Remote not working: Verify the battery is correctly installed and charged. Ensure the remote is properly programmed to your receiver. Check if the receiver unit has power and is functioning correctly.
- Reduced range: This often indicates a low battery. Replace the battery. Ensure there are no significant physical obstructions (e.g., thick walls, metal structures) between the remote and the receiver.
- Interference: Other radio frequency devices in the vicinity might cause interference. Try operating the remote from a slightly different position or distance.
- Incorrect operation: If the remote activates the wrong function or behaves erratically, re-program the remote control following the detailed steps in your receiver's manual.
Specifications
| Feature | Detail |
|---|---|
| Brand | BENINCA |
| Model | TO.GO 2WV |
| Part Number | OR-479 |
| Frequency | 433.92Mhz |
| Code Type | Rolling Code |
| Buttons | 2 |
| Item Weight | 1.41 ounces |
| Package Dimensions | 3.15 x 1.57 x 0.79 inches |
| Date First Available | February 2, 2017 |
Warranty and Support
For specific warranty information, technical assistance, or to purchase replacement parts, please contact your authorized BENINCA product supplier or refer to the documentation originally provided with your BENINCA gate or garage door opener system. It is advisable to retain your purchase receipt for any warranty claims.
