1. Introduction
The Paslode IM350+ Framing Nailer is a powerful, gas-powered tool designed for professional framing applications. It offers excellent power-to-weight ratio and is equipped with a quick-charge Lithium battery, capable of delivering up to 9,000 shots per charge. This manual provides essential information for the safe and efficient operation, maintenance, and troubleshooting of your IM350+ nailer.
Figure 1: Front view of the Paslode IM350+ Framing Nailer.
2. Safety Information
Always observe the following safety precautions to prevent injury and damage to the tool.
- Eye Protection: Always wear ANSI Z87.1 approved safety glasses with side shields.
- Hearing Protection: Wear hearing protection during operation.
- Hand Protection: Wear appropriate gloves to protect hands.
- Work Area: Keep the work area clean, well-lit, and free from obstructions. Do not operate in explosive atmospheres.
- Tool Handling: Never point the tool at yourself or others. Keep fingers away from the trigger when not driving fasteners.
- Disconnect Power: Disconnect the battery and gas cartridge before performing any adjustments, clearing jams, or servicing the tool.
- Fastener Compatibility: Use only fasteners recommended by Paslode for the IM350+.
- Gas Cartridge Safety: Store gas cartridges in a cool, dry place away from direct sunlight and heat sources. Do not puncture or incinerate.
3. Package Contents
Upon opening the high-impact carry case, verify that all the following items are included:
- Paslode IM350+ Framing Nailer
- Lithium battery
- Lithium battery charger
- Cleaning solution
- Impulse lubricant
- Safety glasses
- Allen key
- Instruction manual (this document)
- High impact carry case
4. Setup
4.1. Charging the Lithium Battery
The Paslode IM350+ uses a Lithium-Ion battery. Ensure the battery is fully charged before first use.
- Insert the Lithium battery into the provided Lithium battery charger.
- Plug the charger into a standard electrical outlet.
- The charger's indicator light will show the charging status. A full charge typically takes a short period, providing up to 9,000 shots.
- Once charged, remove the battery from the charger.
Figure 2: Side view of the nailer, showing the battery compartment location.
4.2. Inserting the Gas Cartridge
The IM350+ is gas-powered. A fresh gas cartridge is essential for proper operation.
- Ensure the battery is removed for safety.
- Locate the gas cartridge compartment, usually near the handle.
- Insert the gas cartridge firmly until it clicks into place.
- Reinsert the charged Lithium battery.
4.3. Loading Nails
The nailer uses collated framing nails.
- Pull back the nail pusher until it locks into place.
- Insert a strip of collated nails into the magazine, ensuring the nail points are facing forward.
- Release the nail pusher, allowing it to push the nails forward into the firing position.
Figure 3: View of the nailer's magazine for loading fasteners.
5. Operating Instructions
5.1. Firing the Nailer
To operate the IM350+:
- Ensure safety glasses and hearing protection are worn.
- Place the nose of the tool firmly against the workpiece. The contact trip mechanism must be fully depressed.
- Pull the trigger to fire a nail. The tool will cycle, driving the nail and preparing for the next shot.
- For sequential firing, release the trigger and lift the tool from the workpiece slightly before re-depressing the nose and pulling the trigger again.
5.2. Adjusting Depth of Drive
The depth at which nails are driven can be adjusted to suit different materials and applications.
- Locate the depth adjustment mechanism, typically a rotating wheel or lever near the nose of the tool.
- Rotate the wheel or adjust the lever to increase or decrease the nail's penetration depth. Test on a scrap piece of material to achieve the desired depth.
Figure 4: View of the nailer, highlighting the depth adjustment feature.
6. Maintenance
Regular maintenance ensures optimal performance and extends the life of your Paslode IM350+.
- Daily Cleaning: After each use, especially in dusty environments, clean the tool's exterior with a dry cloth.
- Weekly Cleaning (Internal): As recommended by Paslode, perform an internal cleaning using the provided cleaning solution. Refer to the detailed instructions in the included manual for disassembly and cleaning of internal components. This is crucial for preventing misfires and ensuring consistent operation.
- Lubrication: Apply Impulse lubricant to designated points as per the manufacturer's guidelines. Proper lubrication is vital for the tool's moving parts.
- Battery Care: Store the Lithium battery in a cool, dry place. Do not allow it to fully discharge for extended periods. Charge regularly, even when not in use, to maintain battery health.
- Nose Piece Inspection: Regularly inspect the nose piece for wear or damage. Replace if necessary.
- Air Filter: Check and clean the air filter periodically to ensure proper airflow for combustion.
7. Troubleshooting
This section addresses common issues you might encounter with your IM350+ nailer.
| Problem | Possible Cause | Solution |
|---|---|---|
| Tool does not fire or misfires |
|
|
| Nails not driven to full depth |
|
|
| Nails jam frequently |
|
|
For issues not listed here, or if solutions do not resolve the problem, please contact Paslode customer support.
8. Specifications
| Feature | Detail |
|---|---|
| Model Number | IM350+ |
| Manufacturer | Paslode |
| Power Source | Gas |
| Battery Type | Lithium Ion (1 included) |
| Shots per Charge | Up to 9,000 |
| Product Dimensions | 30.5 x 11 x 37 cm |
| Item Weight | 3.3 kg |
| Colour | Orange |
| Material | Plastic |
| Usage | Professional, Outside |
9. Warranty and Support
For warranty information, please refer to the documentation provided with your purchase or visit the official Paslode website. For technical support, spare parts, or service, please contact Paslode customer service directly. Ensure you have your model number (IM350+) and serial number ready when contacting support.
Paslode Official Website: www.paslode.co.uk
