SCS 718 Static Sensor User Manual

1. Introduction

This manual provides essential information for the proper use, setup, operation, and maintenance of the SCS 718 Static Sensor. The SCS 718 is a handheld device designed for measuring electrostatic charge voltage. It features a red LED lamp for accurate measurement distance guidance and can be used with the 718A Charger (Part No: 718CH) to perform ionizer function checks. This sensor is specifically designed for measuring charged potential.

2. Product Overview

The SCS 718 Static Sensor is a compact and portable instrument used to detect and measure static electricity. Its primary function is to identify and quantify electrostatic charges on surfaces, which is crucial in environments where static discharge can cause damage or interference.

Figure 1: SCS 718 Static Sensor. This image displays the SCS 718 Static Sensor, a handheld device. The front panel features a digital display at the top, below which are three rectangular buttons: 'POWER' on the left, 'RANGE/ZERO' in the center, and 'HOLD' on the right. The device is labeled '718 STATIC SENSOR' with the 'SCS' logo and 'StaticControl.com Made in America Desco Industries' at the bottom.

3. Features

• Electrostatic measurement capability.
• Red LED lamp for accurate measurement distance guidance.
• Compatibility with 718A Charger (Part No: 718CH) for ionizer function checks.
• Measures charged potential.

4. Safety Information

Please read and understand all safety instructions before operating the device. Failure to do so may result in injury or damage to the product.

• Do not expose the device to extreme temperatures, humidity, or direct sunlight.
• Avoid dropping the device or subjecting it to strong impacts.
• Do not attempt to open or modify the device. Refer all servicing to qualified personnel.
• Keep the device away from liquids and corrosive materials.
• Ensure the measurement area is clear of obstructions and potential hazards.

5. Setup

The SCS 718 Static Sensor is designed for immediate use. No battery installation is required as the device does not use batteries.

1. Unpacking: Carefully remove the sensor from its packaging and inspect for any signs of damage.
2. Initial Check: Press the POWER button to turn on the device. The display should illuminate.
3. Zeroing: Before each measurement, ensure the device is zeroed. Point the sensor away from any charged objects and press the RANGE/ZERO button to reset the reading to zero.

6. Operating Instructions

Follow these steps to accurately measure electrostatic charges:

1. Power On: Press the POWER button to activate the sensor.
2. Zero the Sensor: Hold the sensor in free air, away from any charged surfaces. Press the RANGE/ZERO button until the display reads "0.00" or close to zero. This calibrates the sensor for accurate readings.
3. Positioning for Measurement: Point the sensor towards the object or surface you wish to measure. The red LED lamp on the sensor acts as a distance guide. Position the sensor so that the red LED light is focused on the target surface, typically indicating the optimal measurement distance (e.g., 1 inch or 2.5 cm).
4. Read the Display: The display will show the electrostatic charge in kilovolts (kV).
5. Hold Reading: To freeze the current reading on the display, press the HOLD button. Press it again to release the hold and resume live readings.
6. Ionizer Function Check (with 718A Charger):
   • Connect the SCS 718 Static Sensor to the 718A Charger (Part No: 718CH).
   • Follow the instructions provided with the 718A Charger to perform ionizer function checks. This typically involves measuring the decay time of a charge.
7. Power Off: Press the POWER button again to turn off the device when not in use.

7. Maintenance

Proper maintenance ensures the longevity and accuracy of your SCS 718 Static Sensor.

• Cleaning: Use a soft, dry, lint-free cloth to clean the exterior of the sensor. Do not use abrasive cleaners, solvents, or liquids.
• Storage: Store the sensor in a cool, dry place, away from direct sunlight and extreme temperatures. Keep it in its original packaging or a protective case when not in use to prevent dust accumulation and physical damage.
• Calibration: Regular calibration is recommended to maintain measurement accuracy. Refer to DESCO's official website or contact their support for calibration services.

8. Troubleshooting

9. Specifications

10. Warranty and Support

For information regarding product warranty, please refer to the warranty card included with your purchase or visit the official DESCO website. For technical support, troubleshooting assistance, or service inquiries, please contact DESCO customer service through their official channels.

Manufacturer: DESCO

Website: www.desco.com (Example link, actual link may vary)