1. Introduction
The DSC PowerSeries NEO HSM2208 is a low current output module designed to expand the programmable output capabilities of compatible DSC PowerSeries NEO security control panels. This module provides eight additional programmable outputs (PGMs) for integrating various external devices such as relays, sirens, or indicator lights into your security system.
This manual provides detailed instructions for the proper installation, configuration, and maintenance of the HSM2208 module to ensure optimal performance and system integration.
An image showing the DSC PowerSeries NEO HSM2208 Low Current Output Module, featuring its blue circuit board, various electronic components, and a white terminal block for connections.
2. Safety Information
Please read and understand all safety instructions before installing or operating the HSM2208 module. Failure to follow these instructions may result in injury, damage to the product, or improper operation.
- Always disconnect power to the control panel and any connected devices before installing, wiring, or servicing the HSM2208 module.
- Installation should be performed by qualified security professionals or electricians only.
- Observe all local electrical codes, regulations, and standards during installation.
- Do not expose the module to moisture, extreme temperatures, or corrosive environments.
- Ensure that the total current draw from all connected PGM outputs does not exceed the module's specified limits.
3. Package Contents
Verify that all items are present in the package before proceeding with installation:
- 1 x DSC PowerSeries NEO HSM2208 Low Current Output Module
- 1 x Installation Guide (this document)
4. Specifications
| Manufacturer | DSC |
| Model | HSM2208 |
| Compatibility | DSC PowerSeries NEO HS2016, HS2032, HS2064, HS2128 Control Panels |
| Output Type | 8 Programmable Low Current Outputs (PGMs) |
| Operating Voltage | 12 Volts (DC) |
| Material | Copper (circuit board) |
| Dimensions (Approx.) | 5.67 x 3.23 x 1.46 inches (Package) |
| Weight (Approx.) | 2.08 ounces |
5. Setup and Installation
5.1 Pre-installation Checklist
- Ensure the DSC PowerSeries NEO control panel is completely powered down (AC and battery disconnected).
- Have necessary tools available: screwdriver, wire strippers, mounting hardware.
- Confirm the HSM2208 module is compatible with your specific PowerSeries NEO control panel model.
5.2 Mounting the Module
The HSM2208 module is typically mounted within the main control panel enclosure or a separate auxiliary enclosure. Choose a secure location that is protected from environmental factors and allows for proper wiring.
- Identify suitable mounting holes within the enclosure.
- Secure the HSM2208 module using appropriate screws or standoffs. Ensure the module is firmly attached to prevent movement.
5.3 Wiring Connections
The HSM2208 module connects to the PowerSeries NEO control panel via the Corbus (Keybus) terminals. It also provides terminals for connecting external devices to its programmable outputs.
- Corbus Connection: Connect the HSM2208 module's Corbus terminals to the corresponding Corbus terminals on the PowerSeries NEO control panel. Ensure correct polarity:
- Red to Red (+12VDC)
- Black to Black (Ground)
- Yellow to Yellow (Data)
- Green to Green (Data)
- Programmable Output (PGM) Connections: Connect external devices to the PGM terminals (PGM1-PGM8) as required. Each PGM output is a low current output and typically switches to ground when activated. Refer to the external device's documentation for specific wiring requirements.
- Ensure that the current draw of any device connected to a PGM output does not exceed the module's specified limits.
- For higher current applications, an external relay must be used, controlled by a PGM output.
After all wiring is complete, carefully inspect all connections for accuracy and security before restoring power to the control panel.
6. Operating and Configuration
The HSM2208 module's programmable outputs are configured and controlled through the connected PowerSeries NEO control panel's programming menu. The module itself does not have user-operable controls.
- Module Enrollment: After installation and power-up, the control panel should automatically detect the HSM2208 module. Verify its enrollment in the control panel's system information or module supervision section.
- PGM Output Programming: Access the PowerSeries NEO control panel's programming menu (typically Installer Programming) to assign specific functions to each of the eight PGM outputs on the HSM2208 module.
- Common PGM functions include siren activation, strobe light activation, relay control for garage doors or lights, and status indicators.
- Refer to the specific PowerSeries NEO control panel's programming manual for detailed instructions on PGM output assignment, activation conditions, and timing.
- Testing: After programming, thoroughly test each PGM output to ensure it functions as intended with the connected external device.
7. Maintenance
The DSC PowerSeries NEO HSM2208 module is designed for reliable operation and requires minimal maintenance.
- Periodic Inspection: Periodically inspect the module and its wiring connections for any signs of damage, corrosion, or loose connections.
- Environmental Conditions: Ensure the module remains in a clean, dry environment, free from excessive dust, moisture, and extreme temperatures.
- Firmware Updates: Any firmware updates for the module would typically be performed through the connected PowerSeries NEO control panel. Consult your security professional or DSC documentation for information on firmware updates.
8. Troubleshooting
If you encounter issues with the HSM2208 module, consider the following troubleshooting steps:
8.1 Module Not Responding or Not Detected
- Power Check: Ensure the PowerSeries NEO control panel is fully powered (AC and battery connected).
- Corbus Wiring: Verify that the Corbus connections (Red, Black, Yellow, Green) between the HSM2208 and the control panel are secure and correctly wired, observing polarity.
- Module Enrollment: Check the control panel's programming to confirm the HSM2208 module is properly enrolled and recognized by the system. If not, attempt to re-enroll the module.
- Address Conflicts: If multiple modules are on the Corbus, ensure there are no address conflicts (though the HSM2208 typically auto-addresses).
8.2 PGM Output Not Activating
- Programming Verification: Confirm that the specific PGM output is correctly programmed in the control panel with the desired function and activation conditions.
- External Device Check: Verify that the external device connected to the PGM output is functioning correctly when tested independently.
- Current Limits: Ensure the external device's current draw does not exceed the PGM output's specified limits. Overcurrent can prevent activation or damage the module.
- Wiring to Device: Check the wiring between the PGM output and the external device for any breaks, shorts, or incorrect connections.
If issues persist after troubleshooting, contact your authorized DSC dealer or technical support.
9. Warranty and Support
Warranty Information: For detailed warranty terms and conditions applicable to the DSC PowerSeries NEO HSM2208 Low Current Output Module, please refer to the warranty documentation provided with your original purchase or contact your authorized DSC dealer.
Technical Support: Technical assistance for the HSM2208 module is available through your authorized DSC security system installer or dealer. You may also find additional resources, FAQs, and support contact information on the official DSC website.
