CJ Tech 605 2-Outlet Indoor 7-Day Digital Timer User Manual

1. Introduction

This manual provides comprehensive instructions for the safe and efficient operation of your CJ Tech 605 2-Outlet Indoor 7-Day Digital Timer. Please read this manual thoroughly before using the device and retain it for future reference.

The CJ Tech 605 is designed to automate the on/off cycles of indoor electrical devices, offering convenience and energy savings through its programmable 7-day digital timer and two grounded outlets.

2. Important Safety Instructions

• For indoor use only. Do not expose to moisture or extreme temperatures.
• Do not exceed the electrical ratings of the timer. Refer to the specifications section for details.
• Ensure the timer is securely plugged into a grounded outlet.
• Do not use with appliances that could cause a hazardous condition if left unattended, such as heating appliances.
• Do not disassemble or attempt to repair the timer. Contact qualified service personnel for assistance.
• Keep out of reach of children.

3. Package Contents

• 1 x CJ Tech 605 2-Outlet Indoor 7-Day Digital Timer
• 1 x User Manual (this document)

4. Product Features

The CJ Tech 605 timer offers the following key features:

• 2 Grounded Outlets: Control two devices simultaneously.
• 7-Day Digital Programming: Set custom on/off schedules for each day of the week.
• Programmable: Create multiple on/off programs.
• Astronomical Features: Automatically adjusts to sunrise/sunset times (specific implementation details may vary, refer to programming section).
• Manual Override: Temporarily switch devices on or off without affecting programmed settings.
• Built-in Battery Backup: Retains settings during power outages.

Figure 1: The CJ Tech 605 2-Outlet Indoor 7-Day Digital Timer shown in its retail packaging. The timer is white with a digital display and four control buttons: ON/OFF, SET, -/RDM, and +/AUTO. The packaging highlights its features: 2 outlets, 7-day digital timer, programmable, and astronomical features.

5. Setup and Installation

1. Unpack: Carefully remove the timer from its packaging.
2. Initial Charge: Plug the timer into a standard 120V AC grounded wall outlet for at least 30 minutes to charge the internal battery backup. The display should illuminate.
3. Set Current Time: Before programming, set the current time and day. Refer to the "Operating Instructions" section for details on using the SET and +/- buttons.
4. Connect Devices: Plug the appliances you wish to control into the two grounded outlets on the timer. Ensure the appliances' power switches are in the "ON" position if you want the timer to control their power.

6. Operating Instructions

The timer features a digital display and four control buttons:

• ON/OFF: Manually turns the connected devices on or off, overriding current program settings temporarily.
• SET: Used to enter programming mode for setting time, day, and on/off schedules.
• -/RDM: Decreases values during setting. Also activates/deactivates Random mode (RDM) for security lighting.
• +/AUTO: Increases values during setting. Also switches between Manual ON, Manual OFF, and AUTO modes.

6.1. Setting Current Time and Day

1. Press and hold the SET button until the display flashes.
2. Use the +/AUTO or -/RDM buttons to adjust the current hour. Press SET to confirm.
3. Repeat for minutes and then for the current day of the week.
4. Press SET again to exit time setting mode.

6.2. Manual Override

Press the ON/OFF button to cycle through ON, OFF, and AUTO modes. In AUTO mode, the timer follows its programmed schedule. In ON or OFF mode, the timer will remain in that state until manually changed or the next programmed event occurs (depending on model specifics).

7. Programming the Timer

The CJ Tech 605 allows for multiple ON/OFF programs over a 7-day cycle. The exact number of programs may vary. Follow these general steps:

1. Press the SET button repeatedly until "PROG" or "PROGRAM" appears on the display, along with a program number (e.g., "1 ON").
2. Use the +/AUTO or -/RDM buttons to select the desired day(s) for this program (e.g., MON-FRI, SAT-SUN, or individual days). Press SET to confirm.
3. Set the desired ON time using the +/AUTO or -/RDM buttons for hours and minutes. Press SET to confirm.
4. The display will then show "1 OFF". Set the desired OFF time for the same program using the +/AUTO or -/RDM buttons. Press SET to confirm.
5. Repeat steps 2-4 for additional programs (e.g., "2 ON", "2 OFF", etc.).
6. Once all programs are set, press the ON/OFF button to return to normal operating mode. Ensure the timer is in "AUTO" mode for programs to execute.

7.1. Astronomical Feature (Dusk/Dawn)

If your model supports astronomical features, it will automatically adjust ON/OFF times based on local sunrise and sunset. This feature is typically enabled or configured within the programming mode. Consult the display for specific indicators (e.g., "DUSK", "DAWN") when setting programs. You may need to set your geographical region or zip code for accurate operation, though this model's interface suggests a simpler implementation.

8. Maintenance

• Cleaning: Disconnect the timer from the wall outlet before cleaning. Wipe the exterior with a soft, dry cloth. Do not use liquid cleaners or abrasive materials.
• Storage: If storing the timer for an extended period, ensure the internal battery is charged periodically to maintain its life. Store in a cool, dry place.

9. Troubleshooting

10. Specifications

• Model: CJ Tech 605
• Input Voltage: 120V AC, 60Hz
• Max Load: (Typically 15A/1800W Resistive, 10A/1200W Tungsten - Refer to product label for precise ratings)
• Outlets: 2 Grounded Outlets
• Programming: 7-Day Digital
• Internal Battery: NiMH (for backup)
• Package Dimensions: 6.7 x 5 x 2 inches
• Item Weight: 4.8 ounces
• ASIN: B01GVNSW90
• Item Model Number (Manufacturer SKU): 4330939843

Note: Electrical ratings are typical for this type of device. Always refer to the product label for precise specifications.

11. Warranty and Support

CJ Tech products are designed for reliability and performance. For warranty information or technical support, please refer to the contact details provided on the product packaging or visit the official CJ Tech website. Please have your model number (605) and purchase information ready when contacting support.