1. Introduction
The TENGA FLIP 0 (Zero) is a reusable pleasure device designed for personal use. It features an innovative flip-open design for easy cleaning and an intricate internal structure for enhanced sensation. This manual provides essential information for the proper use, care, and maintenance of your device.
2. Safety Information
- For adult use only.
- Do not use if the device appears damaged or cracked.
- Use only water-based lubricants. Oil-based lubricants may damage the elastomer material.
- Clean the device thoroughly before and after each use as instructed in the Maintenance section.
- Discontinue use immediately if any irritation or discomfort occurs. Consult a medical professional if symptoms persist.
- Store in a clean, dry place away from direct sunlight and extreme temperatures.
3. Package Contents
Upon opening the package, verify that all components are present:
- TENGA FLIP 0 (Zero) Device
- Instruction Manual (this document)
- Sample Lubricant (may be included)
4. Setup
- Unpack the Device: Carefully remove the TENGA FLIP 0 from its packaging.
- Initial Cleaning: Before first use, thoroughly wash the device with mild soap and warm water. Rinse completely and allow to air dry.
- Apply Lubricant: Apply a generous amount of water-based lubricant to the entry point and the internal surfaces of the device.
5. Operating Instructions
The TENGA FLIP 0 is designed for intuitive use, providing a unique experience through its internal structure and pressure pads.
- Insertion: Gently insert into the device. The integrated pivot allows for seamless entry.
- Utilizing Pressure Pads: The device features squeezable pressure pads on the exterior. After insertion, you can squeeze these pads at any point to provide focused stimulation and create an internal vacuum. This enhances the sensation by increasing suction and pressure against the internal textures.
- Explore Internal Textures: The elastomer interior is engineered with less dead-space, stimulating all-over. Experiment with different movements and pressure levels to discover the various sensations provided by the intricate internal details, such as the Layered End Orb, Triple Chain Gate, Ridge Wall, and Ripple Dome.
6. Maintenance and Cleaning
The FLIP 0's design prioritizes hygiene and ease of cleaning.
- Flip Open: After use, simply flip the device open. This exposes the entire internal surface for thorough cleaning.
- Wash: Rinse the device under warm running water. Use a mild, pH-neutral soap if desired. Gently rub the internal textures to remove any lubricant residue.
- Rinse Thoroughly: Ensure all soap is rinsed off.
- Air Dry: Place the device in its open position on its stand or in a well-ventilated area to air dry completely. This also accommodates charging if applicable (though this model does not have charging). Avoid using towels or cloths inside the device as they may leave lint.
- Storage: Once completely dry, close the device and store it in a clean, dust-free environment.
7. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Reduced Suction/Vacuum | Insufficient lubricant; air leakage from improper closure or damage. | Ensure adequate lubricant is applied. Check that the device is fully closed and inspect for any visible cracks or damage to the casing or elastomer. |
| Lubricant Leakage | Excessive lubricant; improper insertion; device not fully closed. | Use an appropriate amount of lubricant. Ensure proper insertion technique. Verify the device is securely closed. |
| Device Not Closing Properly | Debris in hinge; damaged latch mechanism. | Inspect the hinge area for any obstructions and clean if necessary. If latches are damaged, contact customer support. |
| Material Degradation (Cracks/Tears) | Use of incompatible lubricants; improper storage; excessive force during use or cleaning. | Always use water-based lubricants. Store properly. Avoid excessive force. If damage occurs, the device may need replacement. |
8. Specifications
| Feature | Detail |
|---|---|
| Model Name | FLIP ZERO |
| Item Model Number | TFZ-001 |
| Brand | TENGA |
| Color | White |
| Material | Thermoplastic Elastomer (TPE) |
| Product Dimensions | 9 x 4 x 4 inches |
| Item Weight | 1.2 Pounds |
| Manufacturer | OneUp Innovations |
| Date First Available | June 24, 2016 |
9. Warranty and Support
For specific warranty information, please refer to the product packaging or the official TENGA website. General support and additional resources may be found through the following links:
For further assistance, please contact TENGA customer support directly via their official channels.
