PIXEL TW-283E3 Wireless Shutter Release Remote Control for Canon Cameras User Manual

Introduction

The PIXEL TW-283E3 Wireless Shutter Release Remote Control is designed to provide photographers with enhanced control over their Canon cameras. This device allows for remote operation of various camera functions, including autofocus, single shooting, continuous shooting, bulb mode, delay shooting, and advanced timer schedule shooting. Utilizing a wireless FSK 2.4GHz control system, it offers a reliable connection over distances exceeding 80 meters, minimizing camera shake and expanding creative possibilities for diverse photographic scenarios such as long exposures, self-portraits, and time-lapse photography.

Package Contents

Please verify that all items listed below are included in your package:

• TW-283 Transmitter (1 unit)
• TW-283 Receiver (1 unit)
• Shutter Connecting Cable (1 unit)
• User Manual (1 unit)

Note: AAA batteries are not included and must be purchased separately.

Product Overview

The PIXEL TW-283E3 system consists of a transmitter and a receiver, designed for intuitive operation. Below are the key components and their functions:

Image: Labeled diagram of the TW-283E3 Transmitter and Receiver, highlighting buttons and display areas.

Transmitter (TW-283) Components:

1. LED Light Indicator: Indicates operational status.
2. Power Switch, Backlit Button: Turns the unit on/off and controls backlight.
3. Number Add Button: Adjusts numerical settings upwards.
4. Shift Left Button: Navigates left through settings.
5. Set/Confirm Button: Confirms selections.
6. LCD Screen: Displays current settings and timer information.
7. Timer Schedule Start/Stop Button: Initiates or halts timed shooting sequences.
8. Number Reduce Button: Adjusts numerical settings downwards.
9. Shift Right Button: Navigates right through settings.
10. Focus Button/Shutter Button: Half-press for autofocus, full-press for shutter release.

Receiver (TW-283RX) Components:

1. LED Light Indicator: Indicates operational status.
2. Power Switch, Backlit Button: Turns the unit on/off and controls backlight.
3. LCD Screen: Displays current channel.
4. Backlit/Channel Add Button: Controls backlight and adjusts channel upwards.
5. Channel Reduce Button: Adjusts channel downwards.

Setup Guide

1. Battery Installation

Both the transmitter and receiver require 2 AAA batteries each (total 4 AAA batteries). Ensure correct polarity when inserting batteries.

Image: Illustration of battery compartment and correct AAA battery orientation for both the transmitter and receiver units.

2. Connecting the Receiver to Your Camera

The receiver connects to your camera via the provided shutter connecting cable. It can be mounted on the camera's hot shoe for stability, or simply left dangling if preferred.

Image: A camera with the TW-283RX receiver attached to the hot shoe and connected via cable for wired operation.

Different camera models may require specific connecting cables. Ensure you have the correct cable for your camera type (e.g., E3 for Canon, DC0/DC2 for Nikon, S1/S2 for Sony).

Image: Visual guide to different interchangeable shutter connecting cables for various camera brands like Fujifilm, Panasonic, Nikon, Canon, and Sony.

3. Powering On and Pairing

To establish a wireless connection, both the transmitter and receiver must be powered on and set to the same channel.

1. Turn on the Receiver: Long press the power button on the receiver. The LCD screen will display the current channel (e.g., CH01).
2. Turn on the Transmitter: Long press the power button on the transmitter.
3. Set Transmitter Channel: Use the arrow keys on the transmitter to navigate to the channel option on the LCD screen. Press the middle setting button and arrow keys to select the desired channel (e.g., CH01).
4. Set Receiver Channel: On the receiver, long press the CH- and CH+ buttons simultaneously to enter channel setting mode. Use the CH- and CH+ buttons to match the channel displayed on the transmitter.
5. Confirm Pairing: Once both units are on the same channel, they are paired. The LED indicator on the receiver will typically show a steady light or flash to confirm connection.

Video: Demonstrates the process of powering on the receiver and transmitter, setting their respective channels, and pairing them for wireless operation with a camera.

Operating Modes

The PIXEL TW-283E3 offers multiple shooting modes to suit various photographic needs. Ensure your camera is set to the appropriate mode (e.g., Single, Continuous, Bulb) to match the remote's function.

Image: Visual representation of the four primary shooting modes available on the TW-283E3 remote: Single, Continuous, Bulb, and Delay Shooting.

1. Single Shooting Mode

For taking individual photos:

• Half-press the transmitter's shutter button to activate autofocus.
• Full-press the transmitter's shutter button to release the shutter and capture a single image.

Image: Demonstrates the half-press function for focusing and the full-press function for triggering the shutter on the remote control.

2. Continuous Shooting Mode

For capturing a series of images rapidly:

• Set your camera to continuous shooting mode.
• On the transmitter, navigate to the continuous shooting mode (often indicated by multiple overlapping rectangles).
• Full-press and hold the transmitter's shutter button to continuously capture images until released.

3. BULB Shooting Mode

Ideal for long exposure photography where the shutter remains open for an extended duration:

• Set your camera to BULB mode.
• On the transmitter, navigate to BULB mode.
• Press the transmitter's shutter button once to open the camera's shutter.
• Press the shutter button again to close the shutter. The transmitter's LCD will display the elapsed exposure time.

4. Delay Shooting Mode

Allows for a set delay before the shutter is released, useful for self-portraits or reducing initial camera shake:

• On the transmitter, navigate to Delay Shooting mode.
• Set the desired delay time (from 1 to 59 seconds) and the number of shots (from 1 to 99).
• Press the Start/Stop button to initiate the countdown and subsequent shooting.

Advanced Settings: Timer Schedule Shooting

The PIXEL TW-283E3 offers comprehensive timer functions for complex shooting sequences, such as time-lapse photography.

Image: Detailed view of the TW-283E3 remote's LCD screen displaying various timer schedule settings like delay, long exposure, interval, number of shots, and repeat functions.

You can configure the following parameters:

• Timer Schedule Delay (DELY): Sets the initial delay before the first shot. Adjustable from 00:00:00 to 99:59:59.
• Long Exposure Timer (LONG): Sets the duration of each exposure. Adjustable from 00:00:00 to 99:59:59. This functions similarly to BULB mode but is automated within the sequence.
• Interval Timer (INTVL): Sets the time between each shot in a sequence. Adjustable from 00:00:01 to 99:59:59.
• Number of Shots (N1): Sets how many photos are taken in one sequence. Adjustable from 1 to 99.
• Repeat Timer Schedule Interval Time (REPT): Sets the interval between repeated groups of shots. Adjustable from 00:00:01 to 99:59:59.
• Repeat Times (N2): Sets how many times the entire sequence (N1 shots with DELY, LONG, INTVL) is repeated. Adjustable from 1 to 99.

To set these parameters, use the arrow keys to navigate between settings and the number add/reduce buttons to adjust values. Press the Set/Confirm button to confirm each setting. Once all parameters are configured, press the Timer Schedule Start/Stop button to begin the automated shooting sequence.

Camera Compatibility

The PIXEL TW-283E3 is specifically designed for a wide range of Canon EOS and PowerShot cameras. Please ensure your camera model is listed below for optimal performance. For other camera brands, different TW-283 variants (e.g., DC0/DC2 for Nikon, S1/S2 for Sony) are available.

Compatible Canon EOS Models:

• R6, R7, R8, R10, EOSR, EOSRP, EOSRA
• XT, XTi, XS, XSi, T1i, T2, T2i, T3, T3i, T4, T4i, T5, T5i, T6i, T6, T7, T7i, T8i, SL1
• EOS 2000D, 1500D, 1300D, 1200D, 1100D, 1000D, 800D, 850D, 760D, 750D, 700D, 650D, 600D, 550D, 500D, 450D, 400D, 350D, 300D, 100D
• 60D, 60Da, 70D, 77D, 80D, 90D, M5

Compatible Canon PowerShot Models:

• G1X, G1X Mark II, G1X Mark III, G3 X, G5 X, G10, G11, G12, G15, G16
• SX60HS, SX50HS, SX70HS

Important Note:

• Some camera remote control interfaces are located next to the lens (e.g., Canon EOS 5D Mark IV, EOS 6D Mark II). Please check your camera's remote control interface before connecting.
• Not compatible with EOS R50, EOS R5C, R50V, EOS R1, EOS R3, EOS R5 MARKII.

Specifications

Troubleshooting

• No Power/Display: Ensure batteries are correctly inserted with the right polarity and are not depleted. Replace with fresh AAA batteries if necessary.
• No Connection/Shutter Not Firing:
  • Verify both transmitter and receiver are powered on.
  • Confirm that both units are set to the same channel. Re-pair if needed (refer to Setup Guide).
  • Check the shutter connecting cable for secure connection to both the receiver and the camera.
  • Ensure the camera is in a compatible shooting mode (e.g., Single, Continuous, Bulb) and not in a mode that overrides external shutter control.
  • Check camera settings to ensure remote control is enabled, if applicable.
• Blurred Images in Long Exposure: While the remote prevents shake from pressing the camera's shutter, external vibrations (e.g., tripod instability, wind) can still cause blur. Ensure your tripod is stable and consider using a heavier setup if needed.
• Limited Range: Ensure there are no significant obstructions between the transmitter and receiver. Large metal objects or dense walls can interfere with the 2.4GHz signal.
• Difficulty with Advanced Settings: Refer to the "Advanced Settings: Timer Schedule Shooting" section and practice adjusting parameters. The interface requires careful navigation using the arrow and set buttons.

Maintenance

• Cleaning: Wipe the units with a soft, dry cloth. Avoid using harsh chemicals or abrasive materials.
• Storage: Store the remote control in a cool, dry place away from direct sunlight and extreme temperatures. Remove batteries if the device will not be used for an extended period to prevent leakage.
• Handling: Handle the units with care to prevent drops or impacts, which could damage internal components or the LCD screens.

Warranty and Support

For warranty information, technical support, or service inquiries, please refer to the contact details provided with your purchase documentation or visit the official PIXEL website. Keep your proof of purchase for any warranty claims.