Nordlux 84923001 Ekollon Single Pendant Lamp User Manual

1. Introduction

Thank you for choosing the Nordlux 84923001 Ekollon Single Pendant Lamp. This manual provides essential information for the safe installation, operation, and maintenance of your new lighting fixture. Please read these instructions carefully before installation and retain them for future reference.

Image 1: Nordlux Ekollon Single Pendant Lamp

2. Safety Instructions

To ensure safe operation and prevent damage, please observe the following safety precautions:

• Electrical Safety: Installation must be performed by a qualified electrician or competent person in accordance with local wiring regulations. Always disconnect the main power supply before commencing any installation, maintenance, or bulb replacement.
• Voltage: This fixture is designed for 230 Volts. Ensure your electrical supply matches this requirement.
• Bulb Type: Use only E27 base bulbs with a maximum wattage of 60W. LED bulbs are recommended for energy efficiency.
• Indoor Use: This product has an IP20 rating, indicating it is suitable for indoor use only. Do not expose to water or high humidity.
• Handling: Handle the glass shade with care to prevent breakage.
• Heat: Allow the lamp to cool completely before touching the bulb or performing maintenance.

3. Package Contents

Please check that all components are present and undamaged before beginning installation:

• 1 x Nordlux Ekollon Single Pendant Lamp (Brushed Steel top, White Glass shade, Fabric Cable)
• 1 x Ceiling Rose / Mounting Bracket
• Mounting Hardware (screws, wall plugs, terminal block)
• 1 x Instruction Manual (this document)

Note: The light bulb is not included and must be purchased separately.

4. Setup and Installation

Follow these steps for safe and correct installation. If you are unsure, consult a qualified electrician.

1. Prepare for Installation:
   • Switch off the main power supply at the circuit breaker or fuse box before starting any work.
   • Ensure you have all necessary tools (screwdriver, drill, wire strippers, etc.).
2. Mark Drilling Points:
   • Hold the ceiling rose/mounting bracket against the ceiling at the desired installation point.
   • Mark the positions for the drilling holes with a pencil.
3. Mount the Bracket:
   • Drill holes at the marked positions. Insert appropriate wall plugs if necessary.
   • Secure the mounting bracket to the ceiling using the provided screws.
4. Wire Connections:
   • Carefully connect the lamp's electrical wires to your household wiring using the terminal block. Ensure correct polarity: Live (L), Neutral (N), and Earth (E).
   • The lamp features a white fabric cable. The length can be adjusted by shortening the cable before making the final electrical connections.
5. Secure the Lamp Body:
   • Once wiring is complete and secure, attach the ceiling rose to the mounting bracket, ensuring all wires are neatly tucked inside.
   • Gently screw the glass shade onto the brushed steel top if it's not pre-assembled.
6. Install the Bulb:
   • Screw an E27 base bulb (max 60W) into the lamp holder.
7. Restore Power:
   • Once installation is complete and all connections are secure, restore power at the circuit breaker.
   • Test the lamp to ensure it functions correctly.

Image 2: Installed Nordlux Ekollon Pendant Lamp

5. Operating Instructions

The Nordlux Ekollon pendant lamp is operated via a standard wall switch connected to its electrical circuit. Simply toggle the switch to turn the light on or off.

• Bulb Type: This fixture uses an E27 screw-in bulb.
• Maximum Wattage: Do not exceed 60 Watts for the bulb. Using a higher wattage bulb can cause overheating and damage to the fixture or pose a fire hazard.
• Energy Efficiency: For optimal energy efficiency, use an E27 LED bulb.

6. Maintenance

Regular maintenance will help prolong the life and appearance of your lamp.

• Cleaning: Disconnect power before cleaning. Wipe the brushed steel and glass surfaces with a soft, dry, or slightly damp cloth. Do not use abrasive cleaners, solvents, or polishes, as these can damage the finish.
• Bulb Replacement:
  • Always switch off the power supply and allow the bulb to cool completely before attempting to replace it.
  • Carefully unscrew the old E27 bulb.
  • Screw in a new E27 bulb, ensuring it does not exceed 60W.
  • Restore power and test the lamp.

7. Troubleshooting

If you encounter issues with your lamp, refer to the following common problems and solutions:

• Lamp Does Not Light Up:
  • Check if the main power supply is on.
  • Ensure the wall switch is in the 'ON' position.
  • Verify the bulb is correctly screwed in and not faulty. Try a new bulb.
  • Inspect wiring connections (only if you are a qualified person and power is off).
• Light Flickers:
  • Ensure the bulb is screwed in tightly.
  • Try a different bulb to rule out a faulty bulb.
  • Check for loose wiring connections (only if you are a qualified person and power is off).
• Lamp Overheats:
  • Ensure the bulb wattage does not exceed the maximum 60W.
  • Ensure there is adequate ventilation around the lamp.

If problems persist after attempting these solutions, please contact Nordlux customer support or a qualified electrician.

8. Specifications

Image 3: Energy Efficiency Label

9. Warranty and Support

Nordlux products are manufactured to high-quality standards and come with a manufacturer's warranty. For specific warranty terms and conditions, please refer to the documentation provided with your purchase or visit the official Nordlux website.

If you require technical assistance, have questions about installation, or need to report a fault, please contact Nordlux customer support. Contact details can typically be found on the Nordlux website or on your purchase receipt.