1. Introduction
Thank you for choosing the Ingco ID8508 Impact Drill. This manual provides essential information for the safe and effective operation, maintenance, and troubleshooting of your new tool. Please read this manual thoroughly before using the drill and keep it for future reference. Proper use and care will ensure long-lasting performance and safety.
The Ingco ID8508 is a versatile corded electric impact drill designed for various drilling tasks in wood, metal, and masonry. It features an 850W motor, variable speed control, and a maximum drilling capacity of 13mm.
2. General Safety Instructions
WARNING: Read all safety warnings, instructions, illustrations, and specifications provided with this power tool. Failure to follow all instructions listed below may result in electric shock, fire, and/or serious injury.
2.1. Work Area Safety
- Keep the work area clean and well-lit. Cluttered or dark areas invite accidents.
- Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust or fumes.
- Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.
2.2. Electrical Safety
- Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock.
- Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges, and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
- Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
- Do not abuse the cord. Never use the cord for carrying, pulling, or unplugging the power tool. Keep cord away from heat, oil, sharp edges, or moving parts. Damaged or entangled cords increase the risk of electric shock.
2.3. Personal Safety
- Always wear eye protection. Use safety glasses, goggles, or a face shield.
- Wear hearing protection when operating power tools for extended periods.
- Dress properly. Do not wear loose clothing or jewelry. Keep your hair and clothing away from moving parts.
- Stay alert, watch what you are doing, and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol, or medication.
3. Product Overview
Familiarize yourself with the components of your Ingco ID8508 Impact Drill before operation.
Figure 3.1: Ingco ID8508 Impact Drill. This image shows the complete drill assembly, including the main body, chuck, auxiliary handle, and power cord connection point.
3.1. Key Components
- Chuck: Holds the drill bit securely.
- Depth Stop: Used to set the desired drilling depth.
- Auxiliary Handle: Provides additional grip and control.
- Mode Selector Switch: Toggles between drilling and impact drilling modes.
- Variable Speed Trigger: Controls the rotational speed.
- Lock-on Button: For continuous operation.
- Forward/Reverse Switch: Changes the direction of rotation.
- Speed Control Dial: Adjusts the maximum speed.
Figure 3.2: Mode Selector Switch. This image highlights the switch used to select between standard drilling (drill icon) and impact drilling (hammer icon) functions.
Figure 3.3: Trigger and Speed Control Dial. This image shows the main power trigger, the lock-on button, and the rotary dial for pre-setting the maximum speed.
4. Setup
4.1. Attaching the Auxiliary Handle
The auxiliary handle can be rotated 360 degrees for optimal positioning. Loosen the handle by twisting it counter-clockwise, position it as desired, and then tighten it by twisting clockwise until secure. Ensure it is firmly attached before operation to maintain control.
4.2. Installing/Removing Drill Bits
- Ensure the drill is unplugged from the power source.
- Insert the chuck key into one of the holes on the chuck.
- Rotate the chuck key counter-clockwise to open the chuck jaws.
- Insert the drill bit fully into the chuck, ensuring it is centered.
- Rotate the chuck key clockwise to tighten the chuck jaws firmly around the drill bit. Remove the chuck key before operating the drill.
- To remove a drill bit, reverse these steps.
4.3. Setting the Depth Stop
Insert the depth stop rod into the hole on the auxiliary handle. Adjust the rod to the desired drilling depth and secure it by tightening the auxiliary handle. This prevents drilling deeper than intended.
5. Operating Instructions
5.1. Powering On/Off and Speed Control
- To Start: Press the variable speed trigger. The speed increases as you press the trigger further.
- To Stop: Release the variable speed trigger.
- Continuous Operation: For prolonged use, press the trigger and then press the lock-on button. To release, press the trigger again.
- Pre-setting Speed: Use the speed control dial (Figure 3.3) to set the maximum rotational speed before starting the drill. This is useful for specific materials or tasks requiring consistent speed.
5.2. Selecting Drilling Mode
The Ingco ID8508 offers two drilling modes:
- Drilling Mode (Drill Icon): For drilling in wood, metal, plastics, and other materials where impact action is not required. Set the mode selector switch (Figure 3.2) to the drill icon.
- Impact Drilling Mode (Hammer Icon): For drilling in masonry, concrete, and brick. Set the mode selector switch (Figure 3.2) to the hammer icon. This mode combines rotation with a hammering action.
Always select the appropriate mode for the material you are working with.
5.3. Forward/Reverse Rotation
The forward/reverse switch, typically located above the trigger, allows you to change the direction of rotation. Use forward rotation for drilling and reverse rotation for removing jammed drill bits or driving/removing screws (if using appropriate accessories).
6. Maintenance
Regular maintenance ensures the longevity and safe operation of your Ingco ID8508 Impact Drill.
6.1. Cleaning
- Always unplug the tool before cleaning.
- Keep the ventilation openings clear to prevent motor overheating. Use a soft brush or compressed air to clean dust and debris from the vents.
- Wipe the tool housing with a damp cloth. Do not use harsh chemicals or abrasive cleaners.
6.2. Carbon Brushes
The carbon brushes are wear parts. If the motor sparks excessively or the drill loses power, the carbon brushes may need replacement. This should ideally be performed by a qualified service technician.
6.3. Storage
Store the drill in a dry, secure location out of reach of children. Protect it from direct sunlight, extreme temperatures, and moisture.
7. Troubleshooting
If you encounter issues with your Ingco ID8508 Impact Drill, refer to the following common problems and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Drill does not start | No power supply Faulty power cord/plug Worn carbon brushes | Check power outlet and connection Inspect cord for damage; replace if necessary Have carbon brushes inspected/replaced by service center |
| Loss of power during operation | Overload Worn carbon brushes | Reduce pressure on the drill Have carbon brushes inspected/replaced by service center |
| Excessive sparking from motor | Worn carbon brushes Motor fault | Have carbon brushes inspected/replaced by service center Contact service center |
| Drill bit gets stuck | Incorrect drilling technique Wrong drill bit for material | Reduce pressure; use appropriate speed Ensure correct drill bit type and size for the material |
8. Specifications
The following are the technical specifications for the Ingco ID8508 Impact Drill:
- Model: ID8508
- Rated Power Input: 850 W
- No-Load Speed: 0-2400 rpm
- Impact Rate: 0-38400 bpm
- Max. Drilling Capacity: 13 mm
- Voltage: 230 Volts (AC)
- Material: Plastic
- Item Weight: 350 g
- Product Dimensions: 28 x 18 x 8 cm
- Power Source: Corded Electric
- Special Features: Portable
9. Warranty and Support
Ingco products are manufactured to high-quality standards. For warranty information, service, or technical support, please refer to the warranty card included with your purchase or contact your local Ingco dealer or authorized service center. Keep your proof of purchase for any warranty claims.
