Redi-Remote Replacement Remote Control Instruction Manual

Introduction

This manual provides comprehensive instructions for the Redi-Remote replacement remote control, designed specifically for use with JBL SDP2 Digital Surround Processor models 750-11342 and RT75011342. This remote is a custom replacement and is not an original JBL product. It offers direct compatibility without requiring programming.

Product Overview

The Redi-Remote replacement remote control features a standard layout with an upper section for primary functions and a lower section for advanced controls, accessible by sliding down a cover. The remote is designed for intuitive operation of your JBL SDP2 Digital Surround Processor.

Remote Control Layout Description:

• Top Section: Contains power, input selection, display, sleep timer, channel, volume, mute, menu, recall, and numeric keypad buttons.
• Bottom Section (Under Sliding Cover): Reveals additional controls for specific functions such as power for other devices (OFF, ON), bypass, VCR controls (VCR1, VCR2), tuner, V-Disc, TV, effect, volume, tape, auxiliary, CD, record zone 2, done, select, and balance adjustments. The cover clearly indicates "SLIDE DOWN" for access.

Setup

Battery Installation:

1. Locate the battery compartment on the back of the remote control.
2. Slide open the battery compartment cover.
3. Insert four (4) AAA batteries, ensuring correct polarity (+ and -) as indicated inside the compartment. Note: Batteries are included with the remote.
4. Close the battery compartment cover securely.

This Redi-Remote replacement control requires no programming. It is pre-configured for immediate use with compatible JBL SDP2 Digital Surround Processors.

Operating Instructions

Basic Functions (Top Section):

• PWR (Power): Turns the JBL SDP2 unit on or off.
• TV/VIDEO: Selects TV or video input sources.
• DISP (Display): Adjusts or cycles through display modes.
• SLEEP: Activates or adjusts the sleep timer function.
• CH+ / CH- (Channel Up/Down): Changes channels.
• VOL+ / VOL- (Volume Up/Down): Adjusts the audio volume level.
• MUTE: Silences or restores audio output.
• MENU: Accesses the system menu.
• RECALL: Recalls the previously selected channel or input.
• Numeric Keypad (0-9, 100, ENT): Directly enters channel numbers or other numerical inputs. "ENT" confirms entries.

Advanced Functions (Lower Section - Slide Down Cover):

To access advanced functions, gently slide down the cover located at the bottom of the remote control. This will reveal additional buttons for specific device controls and audio adjustments.

• OFF / ON: Power control for auxiliary devices (e.g., TV, VCR).
• BYPASS: Activates or deactivates bypass mode.
• VCR1 / VCR2: Selects VCR 1 or VCR 2 input.
• TUNER: Selects the tuner input.
• V-DISC: Selects the V-Disc input.
• TV: Selects the TV input.
• EFFECT: Adjusts sound effects or modes.
• VOLUME (Up/Down Arrows): Fine-tunes volume.
• TAPE: Selects the tape input.
• AUX (Auxiliary): Selects the auxiliary input.
• CD: Selects the CD input.
• RECORD ZONE 2: Initiates recording for Zone 2.
• DONE: Confirms or exits a setting.
• SELECT (Up/Down Arrows): Navigates through menu options.
• BALANCE (Left/Right Arrows): Adjusts audio balance between left and right channels.

Note: Redi-Remotes are designed to control the specific unit they are intended for and cannot be programmed to control auxiliary devices beyond their pre-defined functions.

Troubleshooting

• Remote not responding:
  • Ensure batteries are correctly installed and not depleted. Replace if necessary.
  • Verify there is a clear line of sight between the remote control and the JBL SDP2 unit's infrared receiver.
  • Remove any obstructions between the remote and the unit.
• Specific functions not working:
  • Confirm you are pressing the correct button for the desired function.
  • For advanced functions, ensure the sliding cover is fully open.
  • Remember that this remote is designed for the JBL SDP2 and cannot be programmed for other devices.

Specifications

Support

For any concerns or questions regarding your Redi-Remote replacement remote control, please contact the manufacturer, Redi-Remote, or the seller directly. Refer to your purchase documentation for specific contact information.