1. Introduction
Thank you for choosing the Hansgrohe Talis Select E Basin Tap 71753000. This manual provides essential information for the safe installation, operation, and maintenance of your new basin tap. The Talis Select E tap is designed for modern bathrooms, offering enhanced comfort and water efficiency with its Comfort Zone 240 and Select technology.
Key features include:
- Comfort Zone 240: Provides ample space under the spout for greater freedom of movement.
- Select Cartridge: Allows for intuitive control of water flow and temperature.
- QuickClean Technology: Simplifies the removal of limescale and dirt from the aerator.
- Water Efficiency: Delivers a normal spray at 5 liters per minute at 3 bar pressure.
2. Safety Information
Please read all instructions carefully before installation and use. Retain this manual for future reference.
- Ensure the main water supply is turned off before beginning any installation or maintenance work.
- All installation and maintenance should be performed by a qualified professional if you are unsure.
- Protect the product from frost.
- Avoid using abrasive cleaners or scouring pads on the chrome finish.
- If connecting to a pump system, ensure it is a universal (negative head) pump suitable for high pressure (over 1.0 bar).
3. Package Contents
Verify that all components are present before starting installation:
- Hansgrohe Talis Select E Basin Tap 240 (without waste)
- Mounting hardware
- Connection hoses
- Instruction manual
4. Setup and Installation
The Hansgrohe Talis Select E Basin Tap is designed for deck-mounted installation. Follow these general steps for installation. Refer to the detailed technical drawing for specific dimensions and connections.
- Turn off the main water supply to the installation area.
- Prepare the mounting hole on the basin or countertop. The required hole diameter is approximately 32mm.
- Insert the tap body into the mounting hole.
- Secure the tap from underneath the basin using the provided mounting hardware (washer, nut).
- Connect the hot and cold water supply lines to the tap's flexible hoses. Ensure connections are tight to prevent leaks.
- If using a pump, ensure it is a universal (negative head) pump suitable for high pressure (over 1.0 bar).
- Once all connections are secure, slowly turn on the main water supply and check for leaks.
Figure 1: Technical drawing showing dimensions and connections for the Hansgrohe Talis Select E Basin Tap. Key dimensions include a spout height of 234mm, a spout length of 183mm, and a maximum deck thickness of 40mm.
5. Operating Instructions
The Talis Select E Basin Tap features an intuitive Select button for water flow control and a side lever for temperature adjustment.
Figure 2: A user activating the water flow by pressing the Select button on top of the tap.
- Turning Water On/Off: Press the "Select" button located on the top of the tap to start or stop the water flow.
- Adjusting Temperature: Use the side lever to adjust the water temperature. Move the lever to the left for hotter water and to the right for colder water.
- Water Flow: The tap provides a consistent normal spray with a flow rate of 5 liters per minute at 3 bar pressure, optimized for water efficiency.
6. Maintenance
Regular cleaning and maintenance will ensure the longevity and optimal performance of your Hansgrohe basin tap.
- Cleaning the Chrome Finish: Use only mild soap and water with a soft cloth. Avoid abrasive cleaners, solvents, or scouring pads, as these can damage the chrome surface.
- QuickClean Technology: The aerator is equipped with QuickClean technology. To remove limescale deposits, simply rub your finger over the silicone nozzles on the aerator. This will dislodge any buildup, restoring optimal spray performance.
- Regular Checks: Periodically check all connections for any signs of leaks.
7. Troubleshooting
If you encounter issues with your basin tap, refer to the following common troubleshooting steps:
| Problem | Possible Cause | Solution |
|---|---|---|
| Low water flow | Clogged aerator; partially closed stopcock; low water pressure. | Clean the aerator using QuickClean technology. Ensure stopcocks are fully open. Check household water pressure. |
| Water leaks from connections | Loose connections; damaged seals. | Tighten connections. Inspect and replace seals if damaged. Ensure water supply is off before tightening. |
| Water temperature not adjusting | Issue with hot/cold water supply; faulty cartridge. | Check hot and cold water supply to the tap. If problem persists, contact a qualified plumber or Hansgrohe support. |
If these steps do not resolve the issue, please contact Hansgrohe customer support or a qualified plumber.
8. Specifications
Detailed technical specifications for the Hansgrohe Talis Select E Basin Tap 71753000:
- Model Name: Talis Select E
- Part Number: 71753000
- Brand: Hansgrohe
- Mounting Type: Deck Mount
- Finish Type: Chrome
- Material: Ceramic, Silicone
- Color: Chrome
- Number of Handles: 1 (for temperature control)
- Hole Count: 1
- Spout Height: 240 mm (Comfort Zone 240)
- Spout Length: 183 mm
- Flow Rate: 5 l/min at 3 bar
- Recommended Uses: Basin
- Item Weight: Approximately 2.28 Kilograms (5 pounds)
- Product Dimensions: 1.81 x 8.11 x 12.13 inches (approximate, refer to technical drawing for precise measurements)
- Special Feature: QuickClean, Select Cartridge
9. Warranty
The Hansgrohe Talis Select E Basin Tap 71753000 comes with a 5-year warranty on manufacturing defects. Please retain your proof of purchase for warranty claims. For full warranty terms and conditions, please refer to the official Hansgrohe website or contact their customer service.
10. Support
For further assistance, technical support, or spare parts, please contact Hansgrohe customer service. You can find contact information on the official Hansgrohe website:
When contacting support, please have your model number (71753000) and purchase date available.
