Introduction
This manual provides essential information for the safe and effective installation, operation, and maintenance of your OSRAM SYLVANIA OCTRON 800 ECOLOGIC Linear Fluorescent Lamp, Model 22136. This T8 lamp is designed for general illumination applications, offering neutral white light with a color temperature of 3500K and a high Color Rendering Index (CRI) of 82. Please read this manual thoroughly before installation and retain it for future reference.
Image: OSRAM SYLVANIA OCTRON 800 ECOLOGIC Linear Fluorescent Lamp, Model 22136. This image displays the linear fluorescent tube, typically used in commercial or industrial lighting fixtures.
Safety Information
Always observe the following safety precautions to prevent injury or damage:
- Disconnect Power: Before installing, replacing, or cleaning the lamp, ensure the power supply to the fixture is turned off at the circuit breaker or fuse box.
- Handle with Care: Fluorescent lamps are made of glass and can break. Handle them carefully to avoid injury from broken glass or exposure to internal components.
- Proper Disposal: Fluorescent lamps contain small amounts of mercury. Dispose of lamps according to local, state, and federal regulations. Do not dispose of in regular household trash.
- Compatibility: Ensure the lamp is compatible with your fixture's ballast and socket type (Medium Bi-pin). Using an incompatible lamp can cause damage to the lamp or fixture, or create a fire hazard.
- Do Not Dim: This lamp is not designed for use with dimmers unless explicitly stated on the lamp or packaging.
- Operating Temperature: Ensure the operating environment is within the specified temperature range for fluorescent lamps.
Setup and Installation
Follow these steps for proper installation:
- Power Off: Turn off the power to the lighting fixture at the main circuit breaker.
- Remove Old Lamp (if applicable): Carefully twist the old fluorescent lamp 90 degrees and gently pull it out of the fixture's sockets.
- Inspect Fixture: Check the fixture's sockets and wiring for any signs of damage or wear. Replace any damaged components before proceeding.
- Insert New Lamp: Align the bi-pin ends of the OSRAM SYLVANIA 22136 lamp with the slots in the fixture's sockets. Gently push the lamp into the sockets until the pins are fully seated, then twist the lamp 90 degrees to lock it into place. Ensure the lamp is securely seated and makes good electrical contact.
- Restore Power: Once the lamp is securely installed, restore power to the fixture at the circuit breaker.
- Test: Turn on the light switch to verify proper operation.
Operating Instructions
The OSRAM SYLVANIA 22136 fluorescent lamp operates in conjunction with a compatible fluorescent ballast within your lighting fixture. Once installed, operation is straightforward:
- Power On/Off: Use the wall switch or fixture control to turn the lamp on or off.
- Warm-up Time: Fluorescent lamps may require a brief warm-up period to reach full brightness, especially in colder environments.
- Normal Operation: The lamp will provide consistent, neutral white light during its operational lifespan.
Maintenance
Minimal maintenance is required for the OSRAM SYLVANIA 22136 lamp to ensure optimal performance and longevity.
- Cleaning: Periodically, with the power off and the lamp cooled, gently wipe the lamp surface with a soft, dry, lint-free cloth to remove dust and debris. Do not use liquid cleaners directly on the lamp.
- Lamp Replacement: Replace the lamp when it reaches the end of its rated life (indicated by flickering, dimming, or failure to ignite) or if it becomes damaged. Always replace with a lamp of the same type and wattage to ensure compatibility and proper operation. Refer to the 'Setup and Installation' section for replacement procedures.
- Fixture Inspection: Regularly inspect the lighting fixture for any signs of wear, corrosion, or loose connections. Address any issues promptly.
Troubleshooting
If your lamp is not functioning correctly, try the following troubleshooting steps:
| Problem | Possible Cause | Solution |
|---|---|---|
| Lamp does not light up | No power to fixture Lamp not properly seated Defective lamp Defective ballast Defective starter (if applicable) | Check circuit breaker and wall switch Re-seat the lamp (see Setup) Replace with a new lamp Consult a qualified electrician Replace starter |
| Lamp flickers or cycles on/off | Lamp nearing end of life Incorrect lamp type for ballast Low ambient temperature Defective ballast | Replace the lamp Ensure lamp matches fixture specifications Allow lamp to warm up; ensure proper operating environment Consult a qualified electrician |
| Reduced brightness | Dust/dirt on lamp Lamp nearing end of life Incorrect lamp type | Clean the lamp (see Maintenance) Replace the lamp Ensure lamp matches fixture specifications |
| Ends of lamp are dark | Normal aging Frequent switching Defective ballast | Replace the lamp when performance degrades Minimize frequent on/off cycles Consult a qualified electrician |
If problems persist after attempting these solutions, consult a qualified electrician or contact OSRAM SYLVANIA customer support.
Specifications
Key technical specifications for the OSRAM SYLVANIA OCTRON 800 ECOLOGIC Linear Fluorescent Lamp, Model 22136:
- Model Number: 22136
- Lamp Type: T8 Linear Fluorescent
- Wattage: 17 Watts
- Base Type: Medium Bi-pin
- Color Temperature: 3500 Kelvin (Neutral White)
- Color Rendering Index (CRI): 82
- Initial Lumens: 1,350
- Average Rated Hours: 30,000 hours
- Diameter: 1.098 inches
- Length: 24 inches (approximate, depending on measurement method)
- Product Dimensions: 7.75 x 6.13 x 25 inches (packaging/case dimensions)
- Item Weight: 6.59 pounds (for a case of lamps)
- Ecologic Feature: Designed for environmental responsibility.
Warranty and Support
For information regarding the product warranty, please refer to the documentation provided with your purchase or visit the official OSRAM SYLVANIA website. For technical support or further assistance, please contact OSRAM SYLVANIA customer service through their official channels.