Introduction
This manual provides essential instructions for the safe and efficient operation, setup, and maintenance of your Fengda AS-186A Professional Airbrush Compressor. This oil-free compressor features a 3-liter air tank, automatic start/stop functions, and is designed for various airbrush applications including hobby, tattoo, and general artistic work. Please read this manual thoroughly before use and retain it for future reference.
Safety Instructions
Always observe the following safety precautions to prevent injury or damage to the equipment:
- Ensure the compressor is placed on a stable, level surface in a well-ventilated area.
- Do not operate the compressor near flammable liquids or gases.
- Always disconnect the power supply before performing any maintenance or when the unit is not in use.
- Keep children and pets away from the operating compressor.
- Wear appropriate personal protective equipment, such as eye protection, when operating an airbrush.
- Do not modify the compressor or its components. Use only original replacement parts.
- Avoid touching hot surfaces during or immediately after operation.
- Regularly check all connections for leaks and ensure hoses are in good condition.
- The compressor is designed for airbrushing applications only. Do not use it for other purposes.
Package Contents
Verify that all components are present and undamaged upon unpacking:
- Fengda AS-186A Airbrush Compressor with 3L Tank
- Pressure Regulator with Gauge
- Water Trap and Air Filter
- Power Cord
- Instruction Manual (this document)
- Note: Airbrush guns and hoses are typically sold separately.
Image: The Fengda AS-186A compressor as it appears in its protective packaging, secured with foam inserts.
Setup
- Unpacking: Carefully remove the compressor from its packaging. Inspect for any shipping damage.
- Placement: Position the compressor on a firm, level surface in a clean, dry, and well-ventilated area. Ensure adequate space around the unit for air circulation.
- Connect Air Hose: Attach your airbrush hose (not included) to the air outlet on the pressure regulator. Ensure a secure, airtight connection.
- Power Connection: Plug the power cord into a grounded electrical outlet (220V AC).
- Initial Check: Before turning on, ensure the pressure regulator knob is turned fully counter-clockwise to the lowest pressure setting.
Image: The Fengda AS-186A airbrush compressor, showing the main body, air tank, pressure regulator, and water trap assembly.
Image: A detailed view of the pressure regulator, gauge, and water trap filter assembly on the compressor.
Operating Instructions
- Power On: Flip the power switch to the "ON" position. The compressor will start to fill the air tank until it reaches approximately 4 Bar (58 PSI), then it will automatically shut off.
- Adjust Pressure: Turn the pressure regulator knob clockwise to increase the output air pressure. Observe the gauge to set the desired working pressure for your airbrush. Turn counter-clockwise to decrease pressure.
- Automatic Operation: The compressor features an auto-start at 3 Bar (43 PSI) and auto-stop at 4 Bar (58 PSI). This maintains a consistent air supply and prolongs motor life.
- Airbrushing: Once the desired pressure is set, you can begin airbrushing. The compressor will cycle on and off as needed to maintain tank pressure.
- Power Off: When finished, turn the power switch to the "OFF" position. Disconnect the airbrush hose and drain any moisture from the water trap.
Image: Integrated airbrush holders on the top of the compressor's protective metal case, providing convenient storage for airbrushes during use or breaks.
Maintenance
The Fengda AS-186A compressor is designed to be maintenance-free due to its oil-less piston. However, regular checks are recommended:
- Drain Water Trap: Regularly check and drain any accumulated moisture from the water trap at the bottom of the filter. This prevents moisture from reaching your airbrush.
- Clean Air Filter: Periodically inspect the air filter element. If it appears dirty, clean it according to the instructions provided with the filter, or replace it if necessary.
- Inspect Hoses and Connections: Check all air hoses and connections for wear, cracks, or leaks. Replace damaged hoses immediately.
- Clean Exterior: Wipe down the exterior of the compressor with a damp cloth to remove dust and debris. Do not use harsh chemicals or abrasive cleaners.
- Storage: When not in use for extended periods, store the compressor in a clean, dry environment.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Compressor does not start. | No power; power switch off; thermal overload. | Check power cord and outlet; ensure switch is ON; allow unit to cool down if overheated. |
| Low or no air pressure. | Regulator set too low; air leaks; clogged filter; airbrush malfunction. | Adjust regulator; check hose connections for leaks; clean/replace air filter; check airbrush for clogs. |
| Compressor runs continuously. | Air leak in system; pressure switch malfunction. | Check all connections for leaks; if problem persists, contact support. |
| Excessive moisture in air output. | Water trap full or not draining. | Drain the water trap. Ensure it is functioning correctly. |
Specifications
- Model: FD-186A
- Voltage: 220 Volts (AC)
- Maximum Power: 150 Watts
- Motor Horsepower: 0.20 HP
- Air Flow Capacity: 20-23 Liters Per Minute
- Tank Volume: 3 Liters
- Maximum Pressure: 4 Bars (58 PSI)
- Auto-Start Pressure: 3 Bars (43 PSI)
- Auto-Stop Pressure: 4 Bars (58 PSI)
- Noise Level: 60 Decibels
- Item Weight: 5 Kilograms
- Dimensions (L x W x H): 31.5 x 31.5 x 36 centimetres
- Material: Metal
- Special Features: Portable, Oil-Free, Pressure Regulator, Water Trap, Air Filter
Warranty and Support
For warranty information or technical support, please refer to the documentation provided at the point of purchase or contact your retailer. Keep your purchase receipt as proof of purchase.
Manufacturer: Fenghua Bida Machinery Manufacture CO., LTD.
