Liebherr Fridge Freezer Ice Maker Repair Kit Instruction Manual

1. Introduction

This instruction manual provides essential information for the proper installation, maintenance, and troubleshooting of the Liebherr Fridge Freezer Ice Maker Repair Kit, model 9590335. This kit is designed to replace specific components of your existing Liebherr ice maker to restore its functionality. Please read this manual thoroughly before beginning any repair work.

For additional support or specific model diagrams, please refer to your appliance's original user manual or visit the official Liebherr Store.

2. Safety Information

WARNING: Always disconnect power to the appliance before performing any service or maintenance. Failure to do so can result in electric shock, injury, or death.

• Ensure the refrigerator is unplugged from the wall outlet before starting any repair.
• Wear appropriate personal protective equipment, such as gloves, to prevent injury.
• If you are unsure about any step, consult a qualified service technician.
• Keep all components and tools away from children.

3. Package Contents

The Liebherr Ice Maker Repair Kit typically includes the following components:

• Ice maker housing components (two main plastic frames)
• Ice tray with water inlet tube
• Other small associated parts for assembly

Image 1: Overview of the Liebherr Ice Maker Repair Kit components, including the main housing parts and the ice tray.

Image 2: Another view of the Liebherr Ice Maker Repair Kit, showing the plastic housing and ice tray from a slightly different perspective.

4. Setup and Installation

This repair kit is intended for replacing specific worn or broken parts of an existing Liebherr ice maker. The exact installation procedure may vary slightly depending on your specific Liebherr refrigerator model. It is highly recommended to consult your appliance's service manual or search for model-specific repair videos online for detailed visual guidance.

General Installation Steps:

1. Disconnect Power: Unplug the refrigerator from the electrical outlet.
2. Access Ice Maker: Locate and carefully remove the existing ice maker assembly from your freezer compartment. This usually involves unscrewing it from the freezer wall or ceiling and disconnecting any wiring harnesses.
3. Disassemble Old Unit: Carefully disassemble the old ice maker unit to identify the parts that need replacement with the new kit components. Pay close attention to how each part is connected.
4. Install New Components: Replace the damaged or worn components with the new parts from the repair kit. Ensure all connections are secure and parts are correctly oriented.
5. Reassemble Ice Maker: Reassemble the ice maker unit, ensuring all screws and clips are properly fastened.
6. Reinstall Ice Maker: Mount the repaired ice maker assembly back into the freezer compartment. Reconnect any wiring harnesses.
7. Restore Power: Plug the refrigerator back into the electrical outlet.
8. Test Functionality: Allow several hours for the ice maker to cycle and produce ice. Check for proper operation and ice production.

Note: Some users have found helpful installation videos on platforms like YouTube by searching for "Liebherr ice maker repair" along with their specific refrigerator model number.

5. Operating (Post-Repair)

After successful installation of the repair kit, your Liebherr ice maker should resume normal operation. The ice maker typically takes several hours to cool down and begin producing ice after being reconnected to power. The first few batches of ice may be smaller or irregularly shaped; this is normal as the system purges air and stabilizes.

Initial Operation Checklist:

• Ensure the water supply to the refrigerator is turned on.
• Verify that the ice maker's bail arm (if applicable) is in the down position to allow ice production.
• Check for any leaks around the water inlet tube connection.
• Discard the first few batches of ice to ensure cleanliness.

6. Maintenance

Regular maintenance helps ensure the longevity and efficient operation of your ice maker.

• Clean Ice Bin: Periodically empty and clean the ice storage bin with mild soap and water. Rinse thoroughly.
• Inspect Components: Occasionally inspect the ice maker components for any signs of wear, cracks, or mineral buildup.
• Water Filter: If your refrigerator has a water filter, ensure it is replaced according to the manufacturer's recommendations to prevent mineral buildup in the ice maker.
• Water Supply: Ensure the water supply line is free from kinks or obstructions.

7. Troubleshooting

If your ice maker is not functioning correctly after installing the repair kit, consider the following common issues:

If troubleshooting steps do not resolve the issue, it may indicate a problem with other components of the refrigerator or ice maker not included in this repair kit. Contact Liebherr customer service or a qualified technician for further assistance.

8. Specifications

• Model Number: 9590335
• ASIN: B01933JOZ6
• Package Dimensions: 13.35 x 13.11 x 3.58 inches
• Item Weight: 1.41 Pounds
• Date First Available: March 11, 2016

9. Warranty and Support

This repair kit is a replacement part. Warranty coverage for this specific component may be subject to the terms and conditions of the original appliance warranty or the retailer from whom the kit was purchased. Please retain your proof of purchase.

For detailed warranty information or technical support, please contact Liebherr customer service directly or refer to the warranty documentation provided with your original Liebherr appliance.

You can find more information and contact details on the official Liebherr website or store page.