Introduction
Thank you for choosing the Vidpro XM-L2 XLR Lavalier Microphone. This professional wired microphone is designed to capture clear, high-quality audio for use with DSLRs, camcorders, and video cameras equipped with an XLR input. Its omni-directional polar pattern ensures comprehensive sound pickup, making it ideal for interviews, presentations, and various video production scenarios. The included lapel clip allows for discreet and secure placement, while the foam windscreen minimizes environmental noise.
Package Contents
Please verify that all items listed below are present in your package:
- Vidpro XM-L2 Lavalier Microphone with 20-foot XLR cable
- Lapel Clip
- Foam Windscreen
Image: The Vidpro XM-L2 lavalier microphone, its attached XLR connector, a separate lapel clip, and a foam windscreen.
Setup
- Connect to Device: Locate the XLR input on your DSLR, camcorder, or video camera. Connect the male XLR plug of the XM-L2 microphone cable firmly into the device's XLR input. Ensure a secure connection.
- Phantom Power: The Vidpro XM-L2 microphone requires 48V phantom power to operate. Ensure that your recording device or external audio interface provides 48V phantom power and that it is enabled for the connected XLR input.
- Attach Lapel Clip: Slide the microphone capsule into the provided lapel clip. The clip is designed to securely hold the microphone in place.
- Apply Foam Windscreen: Gently slide the foam windscreen over the microphone capsule. This helps to reduce plosives (harsh 'p' and 'b' sounds) and minimize wind noise during outdoor recordings.
Image: The Vidpro XM-L2 microphone with its packaging, highlighting the requirement for 48V Phantom Power.
Operating Instructions
For optimal audio quality, follow these guidelines:
- Microphone Placement: Attach the lapel clip to the subject's clothing, typically about 6-8 inches (15-20 cm) below the chin. This position generally provides the best balance of voice clarity and ambient sound rejection.
- Cable Management: Route the 20-foot cable discreetly to avoid tangling or accidental disconnections. Secure any excess cable to prevent noise from cable movement.
- Monitor Audio: Always monitor your audio using headphones connected to your recording device. This allows you to identify and correct any issues with sound levels or interference in real-time.
- Adjust Levels: Set the input gain on your recording device to an appropriate level. Aim for audio levels that peak around -6dB to -3dB to prevent clipping and distortion.
Maintenance
- Cleaning: Use a soft, dry cloth to wipe the microphone body and cable. Do not use liquid cleaners or solvents.
- Windscreen Care: The foam windscreen can be gently hand-washed with mild soap and water if it becomes dirty. Allow it to air dry completely before reattaching.
- Storage: Store the microphone and its accessories in a clean, dry place, away from extreme temperatures and humidity. Avoid tightly coiling the cable to prevent damage.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| No sound or very low sound |
|
|
| Distorted or unclear sound |
|
|
| Intermittent sound |
|
|
Specifications
- Transducer: Electret Condenser
- Polar Pattern: Omni-directional
- Frequency Response: 18 KHz
- Output Impedance: 200 Ohm or less
- Audio Sensitivity: 38 Decibels
- Signal-to-Noise Ratio: 78 dB
- Connector: XLR Type
- Cable Length: 20 feet (approx. 6 meters)
- Power Source: 48V Phantom Power (required)
- Compatible Devices: DSLRs, Camcorders, Video Cameras with XLR input
- Included Components: Lapel Clip, Foam Windscreen
- Item Weight: 3.5 Ounces (approx. 99 grams)
Support
For further assistance or inquiries regarding your Vidpro XM-L2 microphone, please visit the official VidPro website or contact their customer support. Keep your purchase receipt for any warranty claims.
Note: Specific warranty terms and conditions may vary. Please refer to the documentation provided at the time of purchase or the manufacturer's website for detailed warranty information.