PIXEL TW-283/N3 LCD Wireless Shutter Release Timer Remote Control User Manual

1. Introduction

The PIXEL TW-283/N3 is a versatile LCD wireless shutter release and timer remote control designed for Canon EOS cameras. It offers both wired and wireless operation, providing photographers with enhanced control over their camera's shutter functions, including single shooting, continuous shooting, bulb mode, delay shooting, and advanced timer schedule shooting. This manual provides detailed instructions for setup, operation, and maintenance of your TW-283/N3 remote control.

2. Product Overview

The TW-283/N3 system consists of a transmitter and a receiver unit. It utilizes international 2.4G transmission technology, offering a remote distance of over 80 meters and strong anti-interference capabilities with 30 selectable channels. The LCD screens on both units facilitate easy handling and setting adjustments.

Key Features:

• Wireless and Wired Operation: Functions as both a wireless and wired shutter release.
• 2.4G Wireless Transmission: Ensures stable and quick response with a range exceeding 80 meters.
• 30 Channels: Minimizes interference from other devices.
• LCD Display: Clear display for settings and status on both transmitter and receiver.
• Multiple Shooting Modes: Supports single shooting, 1S continuous shooting, BULB shooting, delay shooting, and timer schedule shooting.
• Advanced Timer Functions: Customizable delay timer, exposure time, interval time, number of shoots, repeat shooting interval, and repeat times.
• Broad Compatibility: Compatible with various Canon EOS cameras including 7D Series, 5D Series, 6D Mark II, 1D X Mark II, 1D X, 1Ds Mark III, 1Ds Mark II, 1Ds, 1D Mark IV, 1D Mark III, 1D Mark II N, 1D Mark II, 1D, EOS D2000, 5D Mark III, 5DS, 5DS R, 5D Mark II, 5D, 6D, 7D Mark II, 7D, 50D, 40D, 30D, 20D, 10D, D60, D30, EOS-1V, EOS-3.

3. Setup

3.1 Battery Installation

Both the transmitter and receiver units require two AAA batteries each. Ensure correct polarity when inserting the batteries.

Figure 3.1: Battery compartments for transmitter and receiver. Both units require 2 AAA batteries. Ensure correct polarity during installation.

3.2 Connecting to Camera

The TW-283/N3 can be connected to your camera in two ways: wired or wireless.

• Wireless Mode:
  1. Mount the receiver unit onto your camera's hot shoe.
  2. Connect the provided camera connecting cable from the receiver unit to your camera's remote control terminal.
  3. Ensure both the transmitter and receiver are powered on and set to the same channel.
• Wired Mode:
  1. Connect the camera connecting cable directly from the transmitter unit to your camera's remote control terminal.
  2. The receiver unit is not required for wired operation.

Figure 3.2: Wired and Wireless connection methods. The remote can be used directly wired to the camera or wirelessly via the receiver unit.

Note: If you need a longer cable for wired operation, standard 3.5mm headphone jack extension plugs can be used.

4. Operation

The TW-283/N3 offers various shooting modes. Use the navigation buttons on the transmitter to select and adjust settings.

Figure 4.1: Overview of available shooting modes on the TW-283/N3.

4.1 Single Shot Mode

1. Set the transmitter to single shot mode.
2. Set your camera to single shot mode.
3. Press the shutter button on the transmitter to take a single photograph.

4.2 Continuous Shooting Mode

1. Set the transmitter to continuous mode.
2. Set your camera to continuous shooting mode (e.g., high-speed continuous).
3. Press and hold the shutter button on the transmitter. The camera will continue to take photos until the button is released or the set number of shots is reached (if configured).

4.3 Bulb Shooting Mode

1. Set the transmitter to bulb mode.
2. Set your camera to bulb mode.
3. Press the shutter button on the transmitter once to open the shutter.
4. Press the shutter button on the transmitter again to close the shutter. The LCD screen will display the elapsed exposure time.

4.4 Delay Shooting Mode

This mode allows you to set a delay before the camera starts shooting and specify the number of shots.

1. Set the transmitter to delay mode.
2. Press the center button on the transmitter to enter settings.
3. Adjust the delay time (from 1s to 59s) and the number of shots (from 1 to 99).
4. Set your camera to single shot or continuous shooting mode as desired.
5. Press the shutter button on the transmitter. After the countdown, the camera will take the specified number of shots.

4.5 Timer Schedule Shooting Mode

This advanced mode allows for complex time-lapse and interval shooting sequences.

Figure 4.2: Detailed view of timer schedule settings.

1. Set the transmitter to timer mode.
2. Set your camera to single shot mode and ensure the lens is set to manual focus.
3. Press the center button to access settings and configure the following parameters:
   • Delay (DEL): Time before the first shot (0 sec to 99hrs 59mins 59sec).
   • Long (LONG): Exposure time for each shot (useful for bulb shooting, 0 sec to 99hrs 59mins 59sec).
   • Interval (INTVL): Time between shots (0 sec to 99hrs 59mins 59sec).
   • Number of Shots (N1): How many shots to take in one sequence (1 to 99, or '--' for unlimited).
   • Repeat Interval (REPEAT): Time to wait before repeating the entire sequence (0 sec to 99hrs 59mins 59sec).
   • Repeat Times (N2): How many times to repeat the sequence (1 to 99, or '--' for infinite loop).
4. Once settings are configured, press the Play/Stop button on the transmitter to start the timer sequence.
5. Press the Play/Stop button again to stop the sequence.

5. Specifications

6. Maintenance

• Cleaning: Use a soft, dry cloth to clean the remote control. Avoid using liquid cleaners or solvents.
• Battery Replacement: Replace batteries when the low battery indicator appears on the LCD screen or when the remote's performance degrades. Always replace all batteries in a unit simultaneously.
• Storage: When not in use for extended periods, remove batteries from both the transmitter and receiver to prevent leakage. Store the device in a cool, dry place away from direct sunlight and extreme temperatures.
• Cable Care: Handle the camera connecting cable with care. Avoid bending or pulling it excessively to prevent damage to the connectors.

7. Troubleshooting

8. Warranty and Support

For warranty information or technical support, please refer to the documentation included with your purchase or contact PIXEL customer service through their official website or your retailer. Keep your purchase receipt as proof of purchase.