HURI Primer Bulb and Fuel Line Replacement Kit Instruction Manual

1. Product Overview

This HURI replacement kit provides essential components for the fuel system of various outdoor power tools. It includes primer bulbs and fuel line tubing designed to restore proper fuel delivery and engine starting functionality.

1.1 Package Contents

• 5 x Primer Bulbs
• 2 feet x Fuel Line

1.2 Compatible Models

This kit is compatible with a range of Stihl and McCulloch models, including but not limited to:

• Stihl: MS211, MS211C, MS192T, MS192TC, MS210, MS230, MS250, HT250, FS36, FS40, FS44, FS120, FS120R, FS250, FS250R
• McCulloch: Eager Beaver 282, 287, 28, 297, 327bc, 32bcs, 285, 282 Silver Eagle 28, 32, 2818, 4600, 5000, 3020, 4700, 2012, 3200, 3210, 3214, 3216, 3200, 3205, 3336, Mac 17, 19, 22, 2816, 328, 28, 282, 3227, 327b, 32bc, 2817

2. Safety Information

Always prioritize safety when working with fuel systems and power tools. Failure to follow safety precautions can result in injury or damage.

• Ensure the engine is off and cool before beginning any work.
• Disconnect the spark plug wire to prevent accidental starting.
• Work in a well-ventilated area to avoid inhaling fuel fumes.
• Wear appropriate personal protective equipment (PPE), such as gloves and eye protection.
• Have a fire extinguisher readily available.
• Dispose of old fuel and parts responsibly according to local regulations.

3. Tools Required

The following tools may be necessary for installation:

• Needle-nose pliers
• Small flathead screwdriver
• Utility knife or sharp scissors (for fuel line trimming)
• Hair dryer or heat gun (optional, for softening fuel lines)
• Clean rags

4. Installation Instructions

Follow these steps to replace the primer bulb and fuel lines. Specific procedures may vary slightly depending on your tool model.

4.1 Replacing the Primer Bulb

1. Locate the Primer Bulb: Identify the existing primer bulb on your carburetor or engine housing.
2. Disconnect Fuel Lines: Carefully pull off the fuel lines connected to the old primer bulb. Note which line connects to which nipple (typically one shorter, one longer). If lines are stiff, a hair dryer can be used to gently warm them for easier removal.
3. Remove Old Bulb: The primer bulb is usually held in place by two clasps. Gently pry these clasps to release the old bulb.
4. Install New Bulb: Insert the new HURI primer bulb into the opening, ensuring the clasps snap securely into place.
5. Reconnect Fuel Lines: Attach the fuel lines to the corresponding nipples on the new primer bulb. The shorter nipple typically connects to the fuel tank, and the longer nipple connects to the carburetor. If the fuel lines are difficult to attach, gently warm them with a hair dryer to make them more pliable.

4.2 Replacing Fuel Lines

If your existing fuel lines are cracked, brittle, or leaking, they should also be replaced.

1. Identify Lines: Trace the fuel lines from the primer bulb/carburetor to the fuel tank. Note their routing and connections.
2. Remove Old Lines: Carefully disconnect the old fuel lines from all connection points (primer bulb, carburetor, fuel filter in tank).
3. Cut New Lines: Using the old lines as a guide, cut the new HURI fuel line tubing to the appropriate lengths. Ensure clean, straight cuts.
4. Install New Lines: Route the new fuel lines in the same manner as the old ones. Connect them securely to the primer bulb, carburetor, and fuel filter. Ensure all connections are snug to prevent leaks.

Image 1: HURI Primer Bulb and Fuel Line Kit. This image displays multiple clear primer bulbs with black bases and a coiled length of yellow translucent fuel line tubing, illustrating the components included in the replacement kit.

5. Operating Instructions (After Installation)

After replacing the primer bulb and fuel lines, it is crucial to prime the fuel system before attempting to start the engine.

1. Fill Fuel Tank: Ensure the fuel tank contains fresh, appropriate fuel for your power tool.
2. Prime the System: Press the primer bulb repeatedly (typically 5-10 times) until you see fuel flowing into the bulb and returning to the fuel tank. The bulb should feel firm.
3. Start Engine: Follow your power tool's specific starting procedure.

6. Maintenance

Regular inspection and maintenance can extend the life of your fuel system components.

• Inspect Regularly: Periodically check the primer bulb and fuel lines for cracks, hardening, or signs of leakage.
• Clean: Keep the area around the primer bulb and fuel lines free of dirt and debris.
• Proper Fuel: Always use the correct fuel mixture (if applicable) and fresh fuel to prevent damage to fuel system components.
• Storage: When storing your tool for extended periods, drain the fuel system or use a fuel stabilizer to prevent fuel degradation.

7. Troubleshooting

If you encounter issues after installation, consider the following common problems and solutions:

8. Specifications

9. Warranty and Support

HURI provides a manufacturer warranty for this product.

• Warranty Period: 2 months from the date of purchase.
• Support: For warranty claims or technical assistance, please contact the seller, HURIPARTS, through the platform where the purchase was made.