Skechers Tennyson Digital Watch (Model SR2020) Instruction Manual

Introduction

This manual provides detailed instructions for the Skechers Tennyson Digital Watch, Model SR2020. This watch is designed for daily wear, featuring a digital display, chronograph, alarm, and backlight functions. It is water-resistant to 50 meters (5 ATM), making it suitable for recreational swimming and showering.

Image: Front view of the Skechers Tennyson Digital Watch, Model SR2020, displaying the time and date.

Watch Overview and Button Functions

The Skechers Tennyson Digital Watch features four primary buttons for navigation and function control. Refer to the diagram below for button identification and their general functions.

Image: Diagram illustrating the button layout and key features of the Skechers Tennyson Digital Watch, including Reset, Mode, ST/STP, and Light buttons, along with display indicators for Calendar, Dual Time, Alarm, Hourly Chime, Chronograph, and 12/24 Hour Format.

• MODE Button: Cycles through different modes: Time Display, Chronograph (Stopwatch), and Alarm.
• RESET Button: Used to reset values during setting, or to reset the chronograph.
• ST/STP Button: Starts and stops the chronograph, or adjusts settings in various modes.
• LIGHT Button: Activates the backlight for improved visibility in low-light conditions.

Setup Instructions

Setting Time and Date

1. From the normal time display, press the MODE button three times to enter Time Setting Mode. The seconds will begin to flash.
2. Press the RESET button to cycle through the settings: Seconds → Hours → Minutes → Month → Date → Day of Week.
3. While the desired value is flashing, use the ST/STP button to adjust the value.
4. Once all settings are correct, press the MODE button to exit Time Setting Mode and return to the normal time display.

Setting 12/24 Hour Format

In the normal time display, press the ST/STP button to toggle between 12-hour (with AM/PM indicator) and 24-hour formats.

Operating Instructions

Using the Chronograph (Stopwatch)

1. From the normal time display, press the MODE button once to enter Chronograph Mode. The display will show "00:00:00".
2. Press the ST/STP button to start the chronograph.
3. Press the ST/STP button again to stop the chronograph.
4. Press the RESET button to clear the chronograph to "00:00:00".
5. To return to the normal time display, press the MODE button.

Setting and Using the Alarm

1. From the normal time display, press the MODE button twice to enter Alarm Setting Mode. The alarm hours will begin to flash.
2. Press the ST/STP button to adjust the alarm hour.
3. Press the RESET button to switch to alarm minutes.
4. Press the ST/STP button to adjust the alarm minutes.
5. Press the MODE button to exit Alarm Setting Mode.
6. To turn the alarm ON/OFF, in Alarm Setting Mode, press the ST/STP and RESET buttons simultaneously. An alarm icon will appear/disappear on the display.

Activating the Backlight

Press the LIGHT button at any time to illuminate the display for a few seconds.

Maintenance

Water Resistance

This watch is water resistant to 50 meters (5 ATM). This rating means it is suitable for short periods of recreational swimming and showering. It is not suitable for diving, snorkeling, or high-pressure water activities. Avoid pressing buttons while the watch is wet or submerged to prevent water ingress.

Cleaning

To clean your watch, wipe it with a soft, damp cloth. Avoid using harsh chemicals or abrasive materials, as these can damage the watch case or strap.

Battery Replacement

The watch uses one product-specific battery. When the display dims or functions become erratic, the battery may need replacement. Battery replacement should ideally be performed by a qualified watch technician to ensure the water resistance seal is properly maintained. Improper battery replacement can compromise the watch's water resistance.

Troubleshooting

• Watch display is blank or dim: The battery may be depleted. Refer to the "Battery Replacement" section.
• Time is incorrect: Re-set the time and date following the "Setting Time and Date" instructions. Ensure the 12/24 hour format is set correctly.
• Water appears inside the watch: Immediately cease use and consult a professional watch repair service. This indicates a breach in the water resistance seal.
• Buttons are unresponsive: Ensure the watch is not in a locked mode (if applicable, though not a feature of this model). If the issue persists, a battery replacement or professional inspection may be required.

Specifications

Warranty and Support

For information regarding warranty coverage, please refer to the warranty card included with your purchase or visit the official Skechers website. For technical support or service inquiries, please contact Skechers customer service directly.