1. Introduction
The SOBO WP1000F Aquarium Internal Filter is designed to provide efficient mechanical, biological, and chemical filtration for your aquarium. It ensures crystal clear water, promoting a healthy environment for your aquatic life. This filter is fully submersible and suitable for both fresh and saltwater aquariums.
Key Features:
- Filter sponge for dirt absorption and water clarification.
- Fully submersible design.
- Suitable for both fresh and saltwater environments.
- Quiet operation and energy-efficient.
- Easy to clean and maintain.
2. Important Safety Instructions
Please read all instructions carefully before operating this appliance to prevent injury or damage.
- Always disconnect the power supply before performing any maintenance or cleaning.
- Ensure the filter is fully submerged in water before connecting it to the power supply. Operating the filter dry can cause damage.
- Do not operate any appliance with a damaged cord or plug, or if it malfunctions or has been dropped or damaged in any manner.
- This appliance is intended for indoor use only. Do not use it for purposes other than its intended use.
- Keep out of reach of children.
- Ensure the voltage and frequency of your power supply match the specifications of the filter (220-240V, 50/60Hz).
- Never pull the cord to unplug the filter from the outlet. Grasp the plug and pull to disconnect.
3. Product Overview
The SOBO WP1000F internal filter consists of a motor head, a filter casing, and a filter sponge. It is designed for easy installation and effective water circulation and purification.
Figure 1: SOBO WP1000F Aquarium Internal Filter, front view showing the filter unit and power cord.
Figure 2: SOBO WP1000F Aquarium Internal Filter, side view showing the suction cups for mounting.
4. Setup Instructions
- Unpack the Filter: Carefully remove all components from the packaging. Inspect the filter for any signs of damage.
- Assemble the Filter: Ensure the filter sponge is correctly placed inside the filter casing. Attach the motor head securely to the top of the filter casing.
- Attach Suction Cups: The filter comes with suction cups. Attach these to the motor head or filter body as designed, ensuring they are firmly in place.
- Position in Aquarium: Place the filter inside your aquarium, ensuring it is fully submerged in water. Use the suction cups to firmly attach the filter to the inner glass wall of the aquarium. The filter outlet should be positioned to create good water circulation.
- Connect to Power: Once the filter is securely placed and fully submerged, connect the power plug to a suitable electrical outlet.
5. Operating Instructions
- Initial Start-up: After connecting to power, the filter will immediately begin to operate, drawing water through the filter sponge and expelling clean water.
- Continuous Operation: For optimal water quality, the filter should operate continuously.
- Water Flow: The filter is designed to provide a consistent flow rate of 650 L/H. Ensure the outlet is not obstructed to maintain proper circulation.
6. Maintenance
Regular maintenance is crucial for the longevity and efficiency of your SOBO WP1000F filter and for maintaining healthy aquarium water.
6.1. Cleaning Frequency
The filter sponge should be cleaned regularly, typically every 1-2 weeks, depending on the bioload of your aquarium. The motor unit and impeller should be inspected and cleaned monthly.
6.2. Cleaning Procedure
- Disconnect Power: Always unplug the filter from the electrical outlet before attempting any cleaning or maintenance.
- Remove Filter from Aquarium: Carefully remove the filter from the aquarium. It may contain water, so have a bucket ready.
- Disassemble Filter: Separate the motor head from the filter casing. Remove the filter sponge.
- Clean Filter Sponge: Rinse the filter sponge thoroughly with old aquarium water (from a water change) or dechlorinated tap water. Avoid using untreated tap water as it can kill beneficial bacteria. Gently squeeze the sponge until clean.
- Clean Motor Unit and Impeller: Carefully detach the impeller cover from the motor head. Remove the impeller and clean it and its housing with a small brush to remove any debris or mineral buildup.
- Reassemble and Reinstall: Once all parts are clean, reassemble the filter in reverse order. Ensure all connections are secure. Place the filter back into the aquarium, ensuring it is fully submerged, and then reconnect the power.
7. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Filter not starting/no power | No power supply; damaged cord/plug; impeller jammed. | Check power outlet and plug connection. Inspect cord for damage. Disconnect power, remove and clean impeller. |
| Reduced water flow | Clogged filter sponge; obstructed impeller; air trapped in filter. | Clean filter sponge. Clean impeller and housing. Gently shake the filter while submerged to release trapped air. |
| Excessive noise/vibration | Impeller not seated correctly; debris in impeller; filter not securely mounted. | Disconnect power, remove and clean impeller, ensure it is seated correctly. Re-secure suction cups to the aquarium wall. |
| Water remains cloudy | Filter media saturated; insufficient filtration for tank size; overfeeding. | Clean or replace filter sponge. Ensure filter is appropriate for tank size. Reduce feeding. Perform partial water changes. |
8. Specifications
- Model: WP-1000F
- Voltage: 220-240V
- Frequency: 50/60Hz
- Power: 15W
- Flow Rate: 650 L/H
- Weight: Approximately 370g (product only), 420g (packaged)
- Product Dimensions (LxWxH): 10.5 x 6.7 x 21 cm
- Manufacturer: SOBO
- Country of Origin: China
9. Warranty and Support
For warranty information and customer support, please refer to the documentation provided with your purchase or contact your retailer. Keep your proof of purchase for any warranty claims.
