1. Important Safety Information
Please read and understand all instructions before beginning installation or operation. Failure to follow these instructions may result in electric shock, fire, property damage, or personal injury.
- Always disconnect power at the service panel before working on the fan.
- All wiring must be performed by a qualified electrician in accordance with all applicable electrical codes and standards.
- Ensure the fan is properly grounded.
- Do not use this fan with any solid-state speed control device unless specifically approved for use with this model.
- This fan is intended for general ventilating use only. Do not use to exhaust hazardous or explosive materials and vapors.
- To reduce the risk of fire or electrical shock, do not expose this fan to water or rain.
2. Product Overview
The FANTECH PBW110F is a 4-inch duct, 110 CFM (Cubic Feet Per Minute) bath fan designed for exterior mounting. This Energy Star rated unit provides efficient ventilation for bathrooms, living rooms, and similar spaces, effectively removing moisture and odors. Its design allows for installation where interior space is limited, making it an ideal solution for various residential and commercial applications.
Image of the FANTECH PBW110F bath fan, showing its compact design suitable for exterior mounting.
3. Installation
Proper installation is crucial for the performance and longevity of your FANTECH PBW110F fan. Consult a qualified professional if you are unsure about any steps.
3.1 Mounting Location
- Select an exterior wall or roof location that allows for direct ducting from the area to be ventilated.
- Ensure the mounting surface is structurally sound to support the fan's weight (approximately 12 pounds).
- Maintain adequate clearance around the fan for airflow and future maintenance.
3.2 Ducting
- Use 4-inch diameter rigid or semi-rigid ducting for optimal performance. Flexible ducting should be kept as straight and taut as possible to minimize airflow resistance.
- Minimize duct length and the number of elbows to ensure maximum airflow.
- Seal all duct connections with duct tape or mastic to prevent air leakage.
3.3 Electrical Connection
- Turn off power at the circuit breaker before proceeding.
- Route appropriate electrical wiring (e.g., 14 AWG) to the fan's junction box.
- Connect the fan's wires to the building's electrical supply wires according to the wiring diagram provided inside the fan's junction box cover. Ensure proper grounding.
- Secure all connections with wire nuts and replace the junction box cover.
- The fan is designed for 120V AC, 60Hz power supply.
4. Operation
The FANTECH PBW110F fan is designed for continuous or intermittent operation. It is typically controlled by a wall switch (not included) or a remote control (if applicable to your setup, though the product specifications mention a remote control type, the fan itself may be wired to a standard switch).
- To activate the fan, turn on the connected wall switch.
- To deactivate the fan, turn off the connected wall switch.
- For optimal moisture removal in bathrooms, operate the fan during and for at least 15-20 minutes after showering or bathing.
5. Maintenance
Regular maintenance ensures efficient operation and extends the life of your fan. Always disconnect power before performing any maintenance.
5.1 Cleaning the Fan Blades and Housing
- Turn off power to the fan at the circuit breaker.
- Carefully remove any exterior grille or cover, if present.
- Using a soft cloth dampened with mild soap and water, wipe down the fan blades and interior/exterior housing.
- Do not allow water to enter the motor or electrical components.
- Allow all parts to dry completely before reassembling and restoring power.
5.2 Motor Lubrication
The fan motor is permanently lubricated and requires no additional oiling.
6. Troubleshooting
If your FANTECH PBW110F fan is not operating correctly, refer to the following common issues and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Fan does not operate | No power supply Loose wiring connection Faulty switch | Check circuit breaker/fuse. Verify all wiring connections are secure (power off). Test or replace the switch. |
| Low airflow | Blocked ducting Dirty fan blades Excessive duct length/bends | Inspect ducting for obstructions. Clean fan blades (see Maintenance). Review ducting layout for efficiency. |
| Excessive noise | Loose mounting Debris in fan Damaged fan blades | Ensure fan is securely mounted. Turn off power and inspect for debris. Contact FANTECH support if blades are damaged. |
If the problem persists after attempting these solutions, contact FANTECH customer support or a qualified electrician.
7. Specifications
| Feature | Specification |
|---|---|
| Brand | FANTECH |
| Model Number | PBW110F |
| Electric Fan Design | Exhaust Fan |
| Power Source | Corded Electric |
| Product Dimensions | 14"D x 11"W x 15"H |
| Room Type | Bathroom, Living Room |
| Recommended Uses | Exhausting |
| Wattage | 14 watts |
| Air Flow Capacity | 110 Cubic Feet Per Minute (CFM) |
| Item Weight | 12 Pounds |
| Specification Met | Energy Star Rated |
| Mounting Type | Ceiling Mount, Wall Mount (Exterior) |
| Included Components | Cord |
8. Warranty and Support
FANTECH products are manufactured to high-quality standards and are typically backed by a manufacturer's warranty. For specific warranty details, including duration and coverage, please refer to the warranty card included with your product or visit the official FANTECH website. Keep your proof of purchase for warranty claims.
For technical assistance, replacement parts, or further inquiries, please contact FANTECH customer support directly. Contact information can usually be found on the manufacturer's website or in the packaging materials.
FANTECH Official Website: www.fantech.net
