LEDMO SMD5630 LED Strip Light User Manual

1. Product Overview

The LEDMO SMD5630 LED Strip Light is a flexible lighting solution designed for various applications. This 16.4-foot (5-meter) strip features 300 high-quality SMD5630 LEDs, providing warm white illumination at approximately 3000K. It operates on 12V DC power and has an IP65 waterproof rating, making it suitable for both indoor and outdoor use.

• LED Type: High Quality 5630 SMD Top LED
• LED Count: 300 LEDs (60 LEDs/meter)
• Color Temperature: Warm White 2800-3000K
• Brightness: 23-25 Lumens per LED
• Voltage: DC12V
• Length: 16.4 Ft (5 Meter)
• Waterproof Rating: IP65
• Cuttable: Every 3 LEDs at designated marks
• Lifespan: Over 50,000 hours

Figure 1: LEDMO SMD5630 LED Strip Light on a reel, showing the flexible strip with individual LEDs.

2. Safety Information

Please read and understand all safety instructions before installation and use. Failure to follow these instructions may result in electric shock, fire, or other hazards.

• Power Supply: Only use a compatible 12V DC power supply. For a full 16.4 ft (5 meter) strip, a 12V/5A (60 Watt) power supply is recommended. Using an underpowered supply may reduce brightness, and an overpowered supply can damage the strip.
• Electrical Connections: Ensure all connections are secure and properly insulated to prevent short circuits.
• Heat Dissipation: Do not operate the LED strip while it is still wound on the shipping spool for extended periods (more than a few minutes), as this can cause excessive heat buildup and reduce lifespan. Ensure adequate airflow around the strip during operation.
• Cutting: Only cut the LED strip at the designated cut marks (approximately every 2 inches, after every 3 LEDs). Cutting elsewhere will damage the circuit and render that section inoperable.
• Waterproofing: For IP65 waterproof strips, ensure any cut ends are properly sealed with clear RTV silicone glue or similar waterproof sealant to maintain impermeability.
• Adhesive: The adhesive tape provided may not be sufficient for all surfaces. Consider using additional mounting clips or stronger adhesive for secure installation, especially on uneven or porous surfaces.
• Indoor/Outdoor Use: While rated IP65 for outdoor use, ensure all power connections and adapters are also rated for the intended environment.

3. Setup and Installation

Follow these steps for proper installation of your LED strip light.

3.1 Preparation

• Ensure the installation surface is clean, dry, and smooth.
• Measure the desired length for your LED strip.
• If cutting is required, identify the designated cut marks on the strip. These marks are typically indicated by a copper pad and a scissor icon.

3.2 Cutting the LED Strip (If Needed)

1. Locate the designated cut marks on the LED strip. These occur approximately every 2 inches (every 3 LEDs).
2. Using sharp scissors, carefully cut along the center of the copper pads at the desired mark.
3. For IP65 waterproof strips, apply a waterproof sealant (e.g., clear RTV silicone glue) to the cut end to maintain its waterproof integrity.

3.3 Mounting the LED Strip

1. Carefully peel off the covering from the adhesive backing tape on the LED strip.
2. Press the LED strip firmly onto the desired surface. Apply even pressure along the entire length to ensure good adhesion.
3. For long runs or surfaces where the adhesive may be insufficient, use additional mounting clips (not included) to secure the strip.

3.4 Power Connection

1. Connect the LED strip's female connector to a compatible 12V DC power adapter (sold separately).
2. Ensure the power adapter is rated appropriately for the length of the LED strip being used (e.g., 12V/5A for a full 16.4 ft strip).
3. Plug the power adapter into a standard electrical outlet.

Figure 2: Installation and connection diagram, illustrating dimensions, adhesive backing, and power adapter setup.

Figure 3: Visual comparison highlighting the difference between non-waterproof (bare) and waterproof (transparent soft glue layer) LED strips.

4. Operating Instructions

Once installed and powered, the LED strip is ready for use.

• Power On/Off: The LED strip will illuminate when power is supplied to the adapter. To turn off, disconnect power or use a switch on the power adapter or wall outlet.
• Dimming (Optional): If a compatible LEDMO Single Color Dimmer (sold separately) is connected between the power adapter and the LED strip, you can adjust the brightness using the dimmer's controls.
• Remote Control (Optional): If a remote control system is used (sold separately), refer to its specific instructions for operation.

Figure 4: Color Temperature Chart, illustrating the Kelvin scale and typical applications for different light temperatures. This LED strip provides Warm White light (approx. 3000K).

5. Maintenance

The LEDMO SMD5630 LED Strip Light requires minimal maintenance.

• Cleaning: Gently wipe the strip with a dry, soft cloth to remove dust. For waterproof strips, a damp cloth can be used, but ensure no water enters connections. Do not use harsh chemicals or abrasive cleaners.
• Adhesion Check: Periodically check the adhesion of the strip to its surface. If sections begin to peel, re-secure them with additional adhesive or mounting clips.
• Connection Check: Ensure all power connections remain secure and free from corrosion.

6. Troubleshooting

Refer to the following common issues and solutions.

7. Specifications

8. Warranty and Support

This LEDMO SMD5630 LED Strip Light comes with a 1-year warranty from the date of purchase.

For technical support, warranty claims, or any questions regarding the product, please contact LEDMO customer service through the retailer where the product was purchased or visit the official LEDMO website for contact information.