Avidsen 100110 Additional Motion Detector User Manual

Introduction

This user manual provides comprehensive instructions for the installation, operation, and maintenance of your Avidsen 100110 Additional Motion Detector. This device is designed to seamlessly integrate with your existing Avidsen 100108 and 100111 alarm systems, enhancing the security coverage of your premises. Please read this manual carefully before use to ensure proper functionality and safety.

Safety Information

• Do not expose the device to extreme temperatures, direct sunlight, or high humidity.
• Keep the device away from water and other liquids.
• Do not attempt to open or repair the device yourself. Refer all servicing to qualified personnel.
• Dispose of batteries according to local regulations. Do not mix old and new batteries or different types of batteries.
• Ensure the device is installed in a stable location to prevent accidental falls.

Package Contents

Please check that all items are present and in good condition:

• 1 x Avidsen 100110 Motion Detector
• 1 x User Manual (this document)
• Mounting hardware (screws and wall plugs)

Note: Batteries are not included and must be purchased separately. One AA battery is required.

Setup

1. Battery Installation

1. Locate the battery compartment on the back of the motion detector.
2. Open the battery compartment cover.
3. Insert one (1) AA alkaline battery, ensuring the correct polarity (+/-) as indicated inside the compartment.
4. Close the battery compartment cover securely.

2. Mounting the Detector

Figure 1: Front view of the Avidsen 100110 Motion Detector.

1. Choose an optimal location for the motion detector. It should be placed in a corner or on a wall, approximately 2 to 2.5 meters (6.5 to 8 feet) above the floor, ensuring an unobstructed view of the area to be monitored. Avoid placing it near heat sources, direct sunlight, or areas with strong air currents.
2. Mark the drilling points on the wall using the mounting bracket as a template.
3. Drill holes at the marked points and insert the wall plugs.
4. Secure the mounting bracket to the wall using the provided screws.
5. Attach the motion detector to the mounting bracket, ensuring it clicks securely into place.

3. Pairing with Avidsen Alarm System (100108 / 100111)

Refer to your Avidsen 100108 or 100111 alarm system's user manual for specific instructions on adding new wireless accessories. Generally, the process involves:

1. Put your Avidsen alarm system into "pairing mode" or "learning mode."
2. Activate the motion detector (e.g., by pressing its test button or triggering motion in front of it) to send a signal to the alarm system.
3. The alarm system should confirm successful pairing (e.g., with a beep or on-screen message).
4. Test the detector's functionality by walking in its detection area to ensure it triggers the alarm system.

Operating

Motion Detection

The Avidsen 100110 motion detector uses passive infrared (PIR) technology to detect changes in infrared radiation caused by moving objects (like people) within its detection zone. When motion is detected while the alarm system is armed, the detector will send a signal to the main alarm panel, triggering the alarm.

Indicator Light

The small LED indicator on the front of the detector typically flashes when motion is detected or during pairing/testing. Refer to your alarm system's manual for specific indicator light behaviors related to system status.

Maintenance

Cleaning

To maintain optimal performance, periodically clean the sensor lens with a soft, dry, lint-free cloth. Do not use abrasive cleaners or solvents, as these can damage the device.

Battery Replacement

When the battery level is low, your alarm system may indicate a low battery warning for the detector. Replace the battery promptly to ensure continuous protection. Follow the "Battery Installation" steps in the Setup section.

Troubleshooting

Specifications

Warranty

Avidsen products are manufactured to high quality standards. This product is covered by a limited warranty against defects in materials and workmanship from the date of purchase. Please retain your proof of purchase for warranty claims. The warranty does not cover damage caused by improper installation, misuse, neglect, unauthorized repair, or normal wear and tear. For specific warranty terms and conditions, please refer to the warranty card included with your original alarm system or visit the official Avidsen website.

Support

If you encounter any issues or have questions regarding your Avidsen 100110 Motion Detector, please contact Avidsen customer support. You can find contact information on the official Avidsen website or on the packaging of your alarm system. Please have your product model number (AVD-100110) and purchase details ready when contacting support.

For more information and frequently asked questions, visit: www.avidsen.com