UPBRIGHT UA120020E

UpBright 12V AC Adapter User Manual

Compatible with Black & Decker GCO1200, GC01200, GC1200 Series 12V DC Drill Drivers

Introduction

This manual provides instructions for the safe and effective use of your UpBright 12V AC Adapter. This adapter is designed to provide power and charge batteries for various Black & Decker 12V DC cordless drill drivers.

Important Compatibility Note: This adapter is specifically designed for Black & Decker 12V DC cordless drill drivers. The 12V rating refers to the drill's battery voltage, not the charger's output voltage. The charger's output voltage is typically 12V - 15V. Always verify compatibility with your specific drill model and part number before use.

UpBright AC Adapter compatible with Black & Decker 12V drill driver

Image: The UpBright AC adapter shown alongside various Black & Decker 12V cordless drill drivers, illustrating compatibility.

What's Included

  • 1 x UpBright 12V AC Adapter
  • (Optional: Country-specific outlet adapter for international orders)
Close-up of UpBright 12V AC Adapter

Image: A close-up view of the UpBright 12V AC Adapter, showing its barrel round connector and product labeling.

Setup and Connection

  1. Verify Compatibility: Ensure your Black & Decker drill driver model (e.g., GCO1200, GC01200, GC1200) and part number (e.g., 90542490-01, UA120020E) are listed as compatible with this adapter.
  2. Inspect Adapter: Before use, visually inspect the adapter and its cable for any signs of damage. Do not use if damaged.
  3. Connect to Drill: Insert the barrel round connector of the AC adapter firmly into the charging port of your Black & Decker drill driver or its battery charging base.
  4. Plug into Power Outlet: Plug the AC adapter into a standard 100-240VAC 50/60Hz wall outlet.
  5. Charging Indication: Refer to your drill driver's manual for specific charging indicators (e.g., LED lights) to confirm that charging has begun.
UpBright 12V AC Adapter with US plug

Image: The UpBright 12V AC Adapter featuring a standard Type A - 2 pin (North American) power plug.

Operating Instructions

Once connected, the adapter will supply power to your Black & Decker drill driver or charge its battery. The adapter features Over Voltage Protection (OVP), Over Current Protection (OCP), and Short Circuit Protection (SCP) to ensure safe operation.

  • Always ensure the adapter is used in a well-ventilated area.
  • Do not cover the adapter during operation.
  • Disconnect the adapter from the power outlet when not in use or before cleaning.
  • Avoid using the adapter in wet or damp conditions.

Maintenance and Care

  • Cleaning: Disconnect the adapter from the power source and the device. Wipe the adapter with a dry, soft cloth. Do not use liquid cleaners or solvents.
  • Storage: Store the adapter in a cool, dry place away from direct sunlight and extreme temperatures. Avoid tightly coiling the cable to prevent damage.
  • Inspection: Periodically check the adapter and cable for any signs of wear, cuts, or damage. Replace if any damage is observed.

Troubleshooting

ProblemPossible CauseSolution
Device not charging/receiving power.
  • Adapter not properly plugged into outlet.
  • Adapter not properly connected to device.
  • Power outlet is not functional.
  • Device or adapter is faulty.
  • Ensure adapter is fully inserted into a live wall outlet.
  • Verify the barrel connector is securely seated in the device's charging port.
  • Test the outlet with another working appliance.
  • If issues persist, contact customer support.
Adapter feels warm during use.Normal operation.A slight warmth is normal. If the adapter becomes excessively hot or emits smoke/odor, immediately unplug it and discontinue use.

Specifications

  • Input Voltage: 100-240VAC, 50/60Hz
  • Output Voltage: 12V - 15V DC (for 12V drill batteries)
  • Output Current: 200mA (0.2 Amps)
  • Wattage: 2.4 watts
  • Connector Type: Barrel Round Connector
  • Safety Features: Over Voltage Protection (OVP), Over Current Protection (OCP), Short Circuit Protection (SCP)
  • Color: Black
  • Material: Plastic
  • Power Plug: Type A - 2 pin (North American)
  • Compatible Devices: Black & Decker GCO1200, GC01200, GC1200, GCO1200C, GC01200C, GCO1200CL 12V DC Cordless Drill Drivers; Part Numbers: 90542490, 90542490-01, 9054249001, UA120020E, UA120020

Warranty and Support

This UpBright product comes with a warranty to ensure your satisfaction.

  • Warranty: 30 Days Refund, 24 Months Exchange.
  • Customer Support: For any questions, troubleshooting assistance, or warranty claims, please contact your retailer or the UpBright customer service.
UpBright warranty certificate and international plug adapters

Image: A visual representation of the UpBright Limited Warranty Certificate, alongside examples of international plug adapters (AU, EU, UK) that may be included with international orders.

© 2023 UpBright. All rights reserved.