Lightolier Control A600LV-W Astral Preset Slider Dimmer User Manual

Introduction

This manual provides detailed instructions for the safe installation, operation, and maintenance of your Lightolier Control A600LV-W Astral Preset Slider Dimmer. This device is designed for controlling incandescent lighting loads up to 600W at 120VAC, 60Hz. Please read all instructions carefully before beginning installation or use.

Safety Information

WARNING: Risk of Electric Shock. Improper installation can result in serious injury or death.

• Always turn off power at the circuit breaker or fuse box before wiring.
• Install in accordance with all national and local electrical codes.
• If you are unsure about any part of these instructions, consult a qualified electrician.
• Do not use with non-incandescent loads unless specified. This dimmer is designed for incandescent bulbs only.
• Ensure all wire connections are secure and properly insulated.

Package Contents

• Lightolier Control A600LV-W Astral Preset Slider Dimmer
• Mounting Screws
• Wire Connectors
• Instruction Manual (this document)

Image: Packaging for the Lightolier A600LV-W Astral Preset Slider Dimmer, showing the product name and specifications.

Setup and Installation

Follow these steps to install your dimmer switch:

1. Turn Off Power: Locate the circuit breaker or fuse that supplies power to the switch box. Turn off the power completely before proceeding. Verify power is off using a voltage tester.
2. Remove Old Switch: Carefully remove the wall plate and unscrew the existing switch from the wall box. Disconnect the wires from the old switch, noting which wire was connected to which terminal.
3. Identify Wires: You will typically find a hot wire (usually black), a load wire (to the light fixture, often black or red), and a ground wire (bare copper or green). The A600LV-W dimmer has pre-stripped wires for connection.
4. Wire the Dimmer:
   • Connect the dimmer's black wire to the hot (line) wire from the electrical box.
   • Connect the dimmer's other black wire to the load wire (to the light fixture).
   • Connect the dimmer's green or bare copper wire to the ground wire in the electrical box.

   Use appropriate wire connectors and ensure all connections are tight and secure.

5. Mount the Dimmer: Carefully fold the wires into the electrical box. Mount the dimmer into the wall box using the provided screws.
6. Install Wall Plate: Attach the decorative wall plate (not included) over the dimmer.
7. Restore Power: Turn the power back on at the circuit breaker.

Image: The Lightolier A600LV-W Astral Preset Slider Dimmer, showing its internal components and wiring connections.

Operating Instructions

The Lightolier A600LV-W dimmer features a slider for brightness control and a preset function.

• Turning On/Off: Push the small button at the bottom of the slider to turn the lights on or off.
• Adjusting Brightness: Move the main slider up to increase brightness and down to decrease brightness.
• Preset Function: The dimmer will return to the last set brightness level when turned on, provided the slider position has not been changed.

Maintenance

Your Lightolier dimmer requires minimal maintenance.

• Cleaning: To clean the dimmer, wipe it with a soft, damp cloth. Do not use abrasive cleaners or solvents. Ensure power is off before cleaning.
• Bulb Replacement: Always turn off power at the circuit breaker before replacing light bulbs connected to the dimmer.

Troubleshooting

If you experience issues with your dimmer, try the following solutions:

• Lights do not turn on:
  • Check if the circuit breaker is tripped.
  • Ensure all wire connections are secure.
  • Verify that the light bulbs are working and correctly installed.
• Lights flicker or hum:
  • Ensure the total wattage of the incandescent bulbs does not exceed the dimmer's maximum rating (600W).
  • Confirm that only incandescent bulbs are being used.
  • Check for loose wire connections.
• Dimmer is warm to the touch:
  • It is normal for dimmers to feel warm during operation. If it is excessively hot, ensure the load does not exceed 600W and that proper ventilation is maintained in the electrical box.

Specifications

Warranty and Support

Lightolier products are manufactured to high-quality standards. For warranty information or technical support, please refer to the documentation included with your purchase or visit the official Lightolier website. Keep your proof of purchase for warranty claims.

For further assistance, please contact Lightolier customer service through their official channels.