1. Introduction
This manual provides essential information for the installation, operation, maintenance, and troubleshooting of the Franke 88.014 replacement cartridge. This cartridge is specifically designed for use with Franke FF-1350 series faucets to ensure proper water flow and temperature control. Please read these instructions carefully before proceeding with installation or maintenance.
Image of the Franke 88.014 replacement cartridge, a key component for controlling water flow and temperature in compatible Franke FF-1350 faucets.
2. Setup and Installation
Proper installation of the Franke 88.014 cartridge is crucial for optimal faucet performance and to prevent leaks. If you are unsure about any step, it is recommended to consult a qualified plumber.
- Turn Off Water Supply: Locate the hot and cold water supply valves under the sink and turn them off completely. Turn on the faucet to drain any remaining water and relieve pressure.
- Remove Faucet Handle: Depending on your FF-1350 faucet model, you may need to remove a decorative cap or screw to access the handle screw. Use an appropriate screwdriver to remove the handle.
- Access the Cartridge: Remove any retaining nuts, clips, or covers that secure the old cartridge in place. Note the orientation of the old cartridge before removal.
- Remove Old Cartridge: Carefully pull the old cartridge straight out of the faucet body. You may need to gently twist it to loosen it. Inspect the faucet body for any debris or mineral buildup and clean if necessary.
- Install New Cartridge: Insert the new Franke 88.014 cartridge into the faucet body, ensuring it is correctly oriented. The cartridge should sit flush within the faucet body.
- Secure Cartridge: Reinstall any retaining nuts, clips, or covers that hold the cartridge in place. Do not overtighten.
- Reassemble Faucet: Reattach the faucet handle and any decorative caps or screws.
- Restore Water Supply: Slowly turn on the hot and cold water supply valves. Check for any leaks around the faucet base and connections.
- Test Faucet: Operate the faucet to check for proper water flow and temperature control.
3. Operating Instructions
The Franke 88.014 cartridge is an internal component that facilitates the operation of your Franke FF-1350 faucet. Once installed, the faucet will function as designed, allowing you to control water flow and temperature.
- Water Flow: Lift the faucet handle to initiate water flow. The further the handle is lifted, the greater the water flow.
- Temperature Control: Move the faucet handle left for hot water and right for cold water. The cartridge precisely mixes hot and cold water to achieve the desired temperature.
- Shut-off: Push the faucet handle down to stop the water flow.
4. Maintenance
Regular maintenance helps prolong the life of your faucet and cartridge.
- Cleaning: Clean the exterior of your faucet regularly with a soft cloth and mild soap. Avoid abrasive cleaners or harsh chemicals, as these can damage the finish.
- Leak Checks: Periodically inspect the faucet and connections for any signs of leaks. Address minor leaks promptly to prevent further damage.
- Aerator Cleaning: If water flow becomes restricted, unscrew and clean the faucet aerator. Mineral deposits can accumulate and reduce flow.
- Cartridge Replacement: The cartridge is a wear-and-tear item. If you experience persistent dripping, difficulty controlling water temperature, or a stiff handle, it may be time to replace the cartridge again.
5. Troubleshooting
Here are some common issues and their potential solutions related to your faucet cartridge.
| Problem | Possible Cause | Solution |
|---|---|---|
| Faucet is dripping or leaking | Worn cartridge seals, improper installation, or damaged cartridge. | Ensure cartridge is seated correctly. If issue persists, replace the cartridge. |
| Reduced water flow | Clogged aerator, debris in water lines, or partially closed supply valves. | Clean the aerator. Check that water supply valves are fully open. |
| Difficulty turning handle or stiff operation | Mineral buildup, worn internal components of the cartridge. | Consider replacing the cartridge. |
| Inconsistent water temperature | Faulty cartridge, issues with hot/cold water supply. | Verify hot and cold water supply. If supply is fine, replace the cartridge. |
6. Specifications
Key specifications for the Franke 88.014 Cartridge:
- Manufacturer: Franke
- Part Number: 88.014
- Item Weight: 1 pound
- Item Package Quantity: 1
- ASIN: B00TUK6K1E
- Date First Available: February 20, 2015
7. Warranty and Support
For specific warranty information regarding your Franke 88.014 cartridge or FF-1350 faucet, please refer to the documentation provided with your original faucet purchase or visit the official Franke website. For technical assistance or customer support, please contact Franke customer service directly.
You can typically find contact information on the Franke official website or through your product's original packaging.
