1. Introduction and Overview
The SCHLAGE aptiQ MT11 Multi-Technology Mullion Reader is an advanced access control device designed for secure and flexible entry management. This reader supports a wide range of credential technologies, including 125kHz proximity and 13.56MHz contactless smart cards, facilitating seamless transitions or upgrades for existing access control systems. It is FIPS 201-1 compliant and NFC compatible, ensuring readiness for future mobile credential integrations.
Key features of the aptiQ MT11 reader include:
- Multi-technology support for 125kHz proximity and 13.56MHz smart cards.
- FIPS 201-1 compliance for enhanced security standards.
- NFC compatibility for use with aptiQ mobile credentials.
- Designed for quick and easy installation with a standard wiring color scheme.
- Suitable for interior, exterior, metal, and non-metal installation environments.
Figure 1: The SCHLAGE aptiQ MT11 Multi-Technology Mullion Reader. This image displays the sleek, black, vertical design of the reader with a green indicator light illuminated at the top, signifying operational status.
2. Setup and Installation
The aptiQ MT11 reader is designed for straightforward installation. Ensure all local electrical codes and safety regulations are followed during installation.
2.1. Pre-Installation Checklist
- Verify power supply meets reader specifications.
- Ensure appropriate wiring is available for connection to the access control panel.
- Confirm mounting surface is suitable for the mullion form factor.
- Gather necessary tools (screwdriver, drill, wire strippers, etc.).
2.2. Mounting the Reader
- Secure the easy-to-install mounting bracket to the desired surface using appropriate fasteners. The reader accommodates interior, exterior, metal, and non-metal environments.
- Route the wiring through the mounting surface opening to the reader's connection point.
2.3. Wiring Connections
The aptiQ MT11 reader utilizes a quick-connect design and a standard wiring color scheme, which is consistent with most readers in the market. Refer to your access control panel documentation for specific wiring requirements.
- Connect power wires (typically red for positive, black for ground).
- Connect data wires (e.g., green for Data 0, white for Data 1 for Wiegand protocol).
- Ensure all connections are secure and insulated.
2.4. Power-Up and Testing
- Apply power to the reader. The indicator light should illuminate, typically green, indicating successful power-up.
- Present a valid credential to the reader. Observe the indicator light and listen for an audible confirmation (if equipped).
- Verify that the access control panel registers the credential read and grants access as configured.
3. Operating Instructions
The aptiQ MT11 reader is designed for intuitive operation.
3.1. Presenting Credentials
- Proximity Cards: Hold the 125kHz proximity card flat against the reader's surface.
- Smart Cards: Hold the 13.56MHz smart card (MIFARE classic, MIFARE DESFire EV1) flat against the reader's surface.
- NFC Mobile Credentials: Present your NFC-enabled mobile device with an active aptiQ mobile credential near the reader.
3.2. Indicator Lights and Audio Feedback
- Green Light: Indicates successful credential read and access granted (as configured by the access control system).
- Red Light (if applicable): May indicate an invalid credential or access denied.
- Audible Beep: A short beep typically confirms a successful credential read.
The exact behavior of indicator lights and audio feedback may vary based on the configuration of the connected access control system.
4. Maintenance
The aptiQ MT11 reader requires minimal maintenance to ensure optimal performance.
- Cleaning: Periodically wipe the reader's surface with a soft, damp cloth. Avoid abrasive cleaners or solvents that could damage the finish.
- Inspection: Regularly inspect the reader for any signs of physical damage or loose connections. Address any issues promptly to prevent operational problems.
- Environmental Considerations: While designed for various environments, ensure the reader is not exposed to extreme conditions beyond its operational specifications.
5. Troubleshooting
If you encounter issues with your aptiQ MT11 reader, refer to the following common troubleshooting steps.
| Problem | Possible Cause | Solution |
|---|---|---|
| Reader not powering on (no indicator light). | No power supply or faulty wiring. | Check power connections and ensure power is supplied to the reader. Verify wiring integrity. |
| Credential not recognized. | Invalid credential, credential not enrolled, or reader malfunction. | Ensure the credential is valid and enrolled in the access control system. Try a different known-good credential. Contact system administrator. |
| Reader reads credential but access is denied. | Access control system configuration issue. | This indicates the reader is functioning. The issue lies with the access control panel or its programming. Contact your system administrator. |
For persistent issues or advanced troubleshooting, consult your access control system administrator or contact SCHLAGE technical support.
6. Specifications
| Feature | Detail |
|---|---|
| Model Name | aptiQ MT11 Multi-Technology Mullion Reader |
| Item Model Number | 043156369768 |
| Brand | SCHLAGE |
| Dimensions (L x W x H) | 12 x 1.2 x 12 inches |
| Weight | 6.4 ounces |
| Supported Technologies | 125kHz Proximity, 13.56MHz Contactless Smart Cards (MIFARE Classic, MIFARE DESFire EV1), NFC (aptiQ mobile credentials) |
| Compliance | FIPS 201-1 |
| Installation Environments | Interior, Exterior, Metal, Non-metal |
7. Warranty and Support
For detailed warranty information regarding your SCHLAGE aptiQ MT11 Multi-Technology Mullion Reader, please refer to the documentation provided at the time of purchase or visit the official SCHLAGE website.
Technical support and additional resources can be found on the SCHLAGE website.
