1. Introduction
This manual provides detailed instructions for the Sangean WR-1CL Analog AM/FM Clear Table Top Radio. Please read this manual thoroughly before operating the device to ensure proper use and to maximize its performance and longevity. The Sangean WR-1CL features a transparent polyurethane cabinet, offering a unique aesthetic while providing reliable AM/FM reception.
2. Safety Instructions
Observe the following safety precautions to prevent damage to the unit and ensure user safety:
- Do not expose the radio to water or excessive moisture.
- Avoid placing the unit near heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
- Use only attachments/accessories specified by the manufacturer.
- Unplug the unit during lightning storms or when unused for long periods.
- Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
- Ensure proper ventilation around the unit.
3. Package Contents
Verify that all items are present in the package:
- Sangean WR-1CL Radio Unit
- AC Power Cord
- FM Wire Antenna
- User Manual (this document)
4. Product Features
The Sangean WR-1CL radio includes the following key features:
- Transparent Polyurethane Cabinet
- FM/AM 2-Band Tuner
- Tuning and Band Indicators
- Soft and Precise Tuning Mechanism
- Deep Bass Compensation for enhanced audio
- Internal / External Antenna Selector Switch
- 3-inch, 7W Full Range Speaker with Enlarged Magnet
- Tuning LED Indicator
- Band Selecting Knob with Indicator
- Stereo Headphone Jack
- REC Out port
- Aux-in Jack (Note: This feature is disabled on this model)
5. Controls and Indicators
Familiarize yourself with the controls and indicators on your Sangean WR-1CL radio.
Figure 5.1: Front Panel Controls
This image displays the front of the Sangean WR-1CL radio, highlighting the main controls. From left to right, you can see the Volume knob, the Off/AM/FM band selector knob, and the large Tuning knob. Above these, the analog tuning dial is visible, indicating AM and FM frequency ranges. A speaker grille is on the left side.
Figure 5.2: Side View with Clear Cabinet
This image provides a side perspective of the Sangean WR-1CL radio, emphasizing its transparent polyurethane cabinet. The clear casing allows visibility of some internal electronic components, showcasing the unique design of the unit.
- Volume Knob: Rotate to adjust the audio output level.
- Off/AM/FM Band Selector: Turn this knob to power the radio off or select between AM and FM bands.
- Tuning Knob: Rotate this large knob to scan through available radio frequencies.
- Tuning Dial: Displays the current frequency for both AM and FM bands.
- Tuning LED Indicator: Illuminates when a strong signal is received, aiding in precise tuning.
- Stereo Headphone Jack: Located on the rear or side panel, for private listening.
- REC Out: Audio output for connecting to a recording device.
- Internal / External Antenna Selector Switch: Located on the rear panel, allows selection between the built-in antenna or an external antenna.
6. Setup
6.1 Power Connection
The Sangean WR-1CL can be powered by AC current.
- AC Power: Connect the supplied AC power cord to the AC inlet on the rear of the radio and then to a standard 120V 60Hz wall outlet.
- DC Power (Optional): The unit also supports DC-in 12V DC 1A. An appropriate DC adapter (not included) can be used.
6.2 Antenna Connection
Proper antenna setup is crucial for optimal reception.
- FM Antenna: For FM reception, connect the supplied FM wire antenna to the FM antenna terminal on the rear of the radio. Extend the wire fully and position it for best reception.
- AM Antenna: The radio has a built-in AM ferrite bar antenna. For improved AM reception, rotate the radio for the best signal.
- Antenna Selector Switch: If using an external antenna, ensure the Internal / External Antenna Selector Switch on the rear panel is set to "External". For the built-in or supplied wire antenna, set it to "Internal".
7. Operating Instructions
7.1 Powering On and Off
To power on the radio, rotate the Off/AM/FM Band Selector knob from the "Off" position to either "AM" or "FM". To power off, rotate the knob back to "Off".
7.2 Tuning to a Station
- Select the desired band (AM or FM) using the Off/AM/FM Band Selector knob.
- Slowly rotate the large Tuning knob to scan through frequencies.
- Observe the Tuning LED Indicator. It will illuminate when a strong signal is detected, helping you fine-tune to the station.
- Adjust the radio's position or the FM wire antenna for optimal reception.
7.3 Adjusting Volume
Rotate the Volume knob clockwise to increase the volume and counter-clockwise to decrease it.
7.4 Using Headphones
Plug standard stereo headphones into the Stereo Headphone Jack for private listening. The internal speaker will automatically mute when headphones are connected.
7.5 Recording Output (REC Out)
Connect a recording device to the REC Out port on the radio to capture audio broadcasts. Refer to your recording device's manual for specific connection and recording instructions.
8. Maintenance
8.1 Cleaning the Unit
To clean the radio, use a soft, dry cloth. For stubborn marks, a slightly damp cloth with a mild detergent can be used, followed by a dry cloth. Do not use abrasive cleaners or solvents, as these can damage the cabinet finish.
8.2 Storage
If storing the radio for an extended period, unplug it from the power source and store it in a cool, dry place away from direct sunlight and extreme temperatures.
9. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| No power | Power cord not connected; Power outlet not active; Radio turned off. | Ensure AC cord is securely plugged in; Check power outlet with another device; Turn the Band Selector knob to AM or FM. |
| Poor reception / Static | Weak signal; Antenna not properly positioned; Interference from other electronics. | Adjust the FM wire antenna or rotate the radio for AM; Ensure Antenna Selector Switch is correct; Move radio away from other electronic devices. |
| No sound from speaker | Volume too low; Headphones connected; Radio tuned to static. | Increase volume; Disconnect headphones; Tune to an active station. |
10. Specifications
Figure 10.1: Product Dimensions
This image illustrates the physical dimensions of the Sangean WR-1CL radio, showing a length of 9.45 inches, a width of 6.61 inches, and a height of 4.69 inches.
| Feature | Detail |
|---|---|
| Model Number | WR-1CL |
| Tuner Technology | AM, FM |
| AM/MW Frequency | 520 - 1710kHz (10k) |
| Speaker Size | 3 inches |
| Output Power | 7W |
| Impedance | 8 ohms |
| Earphones Output | 5 + 5 mW (monaural) |
| Power Supply | AC 120V 60 Hz / DC-in 12V DC 1A |
| Product Dimensions (WxHxD) | 9.45" x 4.69" x 6.61" |
| Item Weight | 5 lb. 3.1 oz (approx. 2.36 kg) |
| Connectivity Technology | Auxiliary (Note: Aux-in jack is disabled) |
| Special Feature | Internal / External Antenna Selector Switch |
11. Warranty and Support
Sangean products are manufactured to high quality standards. For information regarding warranty coverage, please refer to the warranty card included with your product or visit the official Sangean website. For technical support or service inquiries, please contact Sangean customer service through their official channels.
Online Support: www.sangean.com
