1. Introduction
Thank you for choosing the Eglo MESTRE Wall Lamp. This manual provides essential information for the safe installation, operation, and maintenance of your new lighting fixture. Please read these instructions carefully before beginning installation and retain them for future reference.
2. Safety Instructions
- Electrical Safety: Always disconnect the power supply at the main fuse or circuit breaker before installation, maintenance, or bulb replacement.
- Qualified Installation: Installation should be performed by a qualified electrician or a competent person if you are unsure about electrical wiring.
- Indoor Use Only: This product is designed for indoor use in dry locations only. Do not expose to moisture or direct water.
- Bulb Compatibility: Use only bulbs with an E27 base and a maximum wattage of 60W. Exceeding the maximum wattage can cause overheating and damage to the fixture.
- Handling: Handle the glass shade with care to prevent breakage.
- Cleaning: Do not use abrasive cleaners or solvents on the lamp. Refer to the maintenance section for cleaning instructions.
3. Package Contents
Please check that all parts are present and undamaged before installation.
- Eglo MESTRE Wall Lamp fixture
- Mounting hardware (screws, wall plugs)
- Assembly instructions
Note: Light bulb is not included and must be purchased separately.
4. Setup and Installation
Follow these steps to install your Eglo MESTRE Wall Lamp. If you are not confident with electrical installations, please consult a qualified electrician.
- Prepare for Installation:
- Turn off the main power supply to the circuit where the lamp will be installed.
- Unpack all components and ensure they are intact.
- Mark Mounting Points:
- Hold the mounting bracket against the wall at the desired installation location.
- Mark the drilling points using a pencil.
- Drill Holes and Insert Wall Plugs:
- Drill holes at the marked points using an appropriate drill bit for your wall type.
- Insert the provided wall plugs into the drilled holes.
- Secure Mounting Bracket:
- Attach the mounting bracket to the wall using the screws. Ensure it is firmly secured.
- Connect Electrical Wires:
- Connect the household electrical wires to the lamp's wires according to local electrical codes (typically: Live to Live, Neutral to Neutral, Earth to Earth). Use appropriate terminal blocks.
- Ensure all connections are secure and insulated.
- Attach the Fixture:
- Carefully align the lamp fixture with the mounting bracket and secure it with the provided screws.
- Install the Bulb:
- Screw an E27 bulb (max 60W) into the lamp holder.
- Restore Power:
- Turn the main power supply back on.
- Test the lamp to ensure it functions correctly.
Front view of the Eglo MESTRE Wall Lamp, showcasing its antique brown metal frame, decorative top scrollwork, and beige calcified glass shade.
The Eglo MESTRE Wall Lamp mounted on a light pink wall in a room, providing ambient lighting. A wooden cabinet with glass doors is visible in the background.
5. Operating Instructions
The Eglo MESTRE Wall Lamp is operated via a standard wall switch connected to its electrical circuit. Simply toggle the wall switch to turn the lamp on or off.
6. Maintenance
- Cleaning: Ensure the power is off before cleaning. Wipe the metal parts with a soft, dry cloth. For the glass shade, use a soft, damp cloth and mild detergent if necessary, then dry thoroughly. Do not use abrasive cleaners, solvents, or harsh chemicals.
- Bulb Replacement:
- Turn off the power supply at the main switch.
- Allow the old bulb to cool completely before touching it.
- Carefully unscrew the old E27 bulb.
- Screw in a new E27 bulb (max 60W).
- Restore power and test the lamp.
7. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Lamp does not light up | No power supply Faulty bulb Incorrect wiring | Check main power switch/circuit breaker Replace bulb Check wiring connections (consult electrician) |
| Light flickers | Loose bulb Incompatible bulb Loose wiring connection | Tighten bulb Ensure bulb is compatible (E27, max 60W) Check wiring connections (consult electrician) |
| Lamp overheats | Bulb wattage too high | Replace with a bulb that does not exceed 60W |
If you experience any issues not listed here or if the problem persists, please contact Eglo customer support.
8. Specifications
| Feature | Detail |
|---|---|
| Brand | Eglo |
| Model Name | MESTRE |
| Model Number | 86715 |
| Color | Antique Brown / Gold |
| Material | Steel Alloy, Glass |
| Shade Material | Calcified Glass |
| Shade Color | Beige |
| Style | Wall Lamp / Wall Sconce |
| Dimensions (L x W x H) | 30 cm x 16 cm x 33.5 cm (11.81 x 6.3 x 13.19 inches) |
| Weight | Approx. 1.0 Count (Unit sales volume/weight) |
| Indoor/Outdoor Use | Indoor Only |
| Room Type | Kitchen, Hallway, Entrance |
| Power Source | AC/DC |
| Voltage | 230 Volt |
| Bulb Base | E27 |
| Max Wattage | 60 Watt |
| Number of Lights | 1 |
| Compatible Bulb Type | LED (Energy-saving bulbs can be used) |
| Control Method | Wall Switch |
| Mounting Type | Wall Mounting |
| Assembly Required | No (Minor assembly for installation) |
| EU Energy Efficiency Label | A to G |
Diagram showing the dimensions of the Eglo MESTRE Wall Lamp. The lamp measures approximately 30 cm (11.81 inches) in width and 33.5 cm (13.19 inches) in height.
9. Warranty and Support
For warranty information, please refer to the documentation provided with your purchase or contact your retailer. For technical support or further assistance, please visit the official Eglo website or contact their customer service department.
Eglo Website: www.eglo.com
