Introduction
The Progress Lighting Helm Collection One-Light 11" LED Flush Mount fixture is a contemporary lighting solution designed for both ceiling and wall mounting. Featuring an acrylic diffuser with architectural details, this fixture provides efficient and stylish illumination. This manual provides detailed instructions for the safe installation, operation, and maintenance of your new light fixture.
Important Safety Information
Please read and understand all instructions before beginning installation. Failure to do so may result in electric shock, fire, or other injuries that could be fatal or cause serious damage. All electrical connections must be in accordance with local codes, ordinances, or the National Electric Code (NEC). If you are unfamiliar with electrical wiring, consult a qualified electrician.
- Always disconnect power at the main circuit breaker before installation or maintenance.
- Do not install this fixture in wet locations. It is designed for indoor use only.
- Ensure all connections are secure and properly insulated.
- This fixture is designed for 120 Volts AC.
- Do not attempt to modify the fixture. Any modifications may void the warranty and create a safety hazard.
- The LED light source is integrated and not user-replaceable.
Package Contents
Verify that all components are present before beginning installation:
- Helm Collection LED Flush Mount Fixture (1)
- Mounting Hardware Kit (1)
- Installation Sheet (1)
Setup and Installation
Follow these steps carefully to install your new fixture. It is recommended to have two people for installation.
Step 1: Prepare for Installation
- Turn off power at the circuit breaker or fuse box to avoid electrical shock.
- Remove the old fixture (if applicable) and disconnect all wiring.
- Unpack the new fixture and its components. Keep all parts organized.
Step 2: Mount the Fixture
Image: Front view of the 11-inch LED flush mount fixture in a brushed nickel finish, showcasing its square design and acrylic diffuser.
Image: Diagram showing the dimensions of the fixture, indicating an 11-inch width and 3-3/4 inch height.
- Attach the mounting bracket to the junction box using the provided screws. Ensure it is securely fastened.
- Connect the fixture's wires to the corresponding house wires:
- Connect the black wire (Live) from the fixture to the black wire from the junction box.
- Connect the white wire (Neutral) from the fixture to the white wire from the junction box.
- Connect the green or bare copper wire (Ground) from the fixture to the green or bare copper wire from the junction box.
- Carefully tuck all wires into the junction box.
- Align the fixture with the mounting bracket and secure it using the provided screws. Ensure the fixture is flush against the ceiling or wall.
Step 3: Finalize Installation
- Restore power at the main circuit breaker.
- Test the fixture to ensure it is working correctly.
Operating Instructions
This LED flush mount fixture is designed for simple operation.
- Turning On/Off: Use a standard wall switch connected to the fixture's circuit to turn the light on or off.
- Dimming: This fixture is compatible with most standard dimmer switches. For optimal performance and to avoid flickering, use an LED-compatible dimmer switch. Consult your dimmer switch manufacturer's instructions for proper installation and operation.
Maintenance
To ensure the longevity and appearance of your fixture, follow these maintenance guidelines:
- Cleaning: Always turn off the power and allow the fixture to cool before cleaning. Wipe the fixture with a soft, dry cloth. Do not use abrasive cleaners, solvents, or polishes as they may damage the finish or acrylic diffuser.
- LED Light Source: The LED light source in this fixture is integrated and designed for long-term use. It is not user-replaceable. If the LED light source fails, the entire fixture may need to be replaced.
- Inspection: Periodically inspect the fixture for any loose connections or signs of wear. If any issues are found, disconnect power and consult a qualified electrician.
Troubleshooting
If you experience issues with your fixture, refer to the following common problems and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Fixture does not light up. | No power to the fixture. Loose wiring connection. Faulty wall switch. | Check circuit breaker or fuse. Turn off power, check all wire connections. Test or replace the wall switch. |
| Light flickers or dims inconsistently. | Incompatible dimmer switch. Loose wiring. | Ensure an LED-compatible dimmer is used. Replace if necessary. Turn off power, check all wire connections. |
| Humming noise from fixture. | Incompatible dimmer switch. | Replace with an LED-compatible dimmer switch. |
If the problem persists after trying these solutions, contact Progress Lighting customer support or a qualified electrician.
Specifications
| Attribute | Detail |
|---|---|
| Brand | Progress Lighting |
| Model Name | Helm LED |
| Model Number | P3447-0930K9 |
| Color | Nickel |
| Material | Alloy Steel, Glass (Shade) |
| Style | Contemporary |
| Light Fixture Form | Ceiling |
| Indoor/Outdoor Usage | Indoor |
| Power Source | Corded Electric |
| Installation Type | Flush Mount |
| Light Source Type | LED |
| Finish Type | Brushed |
| Number of Light Sources | 1 (Integrated LED) |
| Voltage | 120 Volts |
| Light Color Temperature | 3000 Kelvin (Warm White) |
| Wattage | 17 watts |
| Brightness | 1211 lumens |
| Efficiency | 71.2 lumens/watt |
| Item Weight | 2.82 pounds |
| Dimensions | 11 inches (Diameter/Width) |
| UPC | 785247188895 |
| Energy Efficiency | Energy Star Certified |
Warranty and Support
This Progress Lighting fixture comes with a 5-year Limited Warranty. This warranty guarantees your complete satisfaction with your purchase and includes professional after-sales customer service support.
For warranty claims, technical assistance, or any questions regarding your product, please contact Progress Lighting customer service.
You can also visit the official Progress Lighting Store on Amazon for more information and product offerings.
